write trucks with galletto v53

[alien78]

hello all I would like to know if anyone has ever tried to write a scania r with ems s7

[davidehfnos]

hello you have connected the v53 clone to 24 v???? the read it all correctly??? according to me as he read the writing

[alien78]

I used the v53 clone the one with the pc and reading ? was made correctly

[sisco]

hello alien 78 also I read a s7 of a scania but with the version 84 of cock 2 (clone)? I have not tried yet to write, in fact if you do know how to v

[Mr.Flash]

I always knew that the rooster clone were limited to 12v..... for? in fact, I have never personally tried it. You have also done the writing ???

[alien78]

no, I have not yet tried to write why? the first truck that me ? happened to you ? a scania and in the case of a block in the process of writing that you can't? do bdm........
but the galletto clone works great 24v

[sisco]

I have read several ecu 24 volt and I have written 3 ms 6.2) and (2 s6 bdm always a24 volt

[davidehfnos]

with the cock, v53?

[nox]

I have read several scania and also iveco cursor with the ms6.2 masi serial've always had problems with edc7 that I have to try in Bdm, However, on 24 volt works I have both the v48 53 but I know that in the round there were of v48 who did not have the rel? 24

[alien78]

so here today I wanted to write the scania r360 but when I open the software of the cock I have seen that is not seen pi? the list of trucks,tractors, and motorcycles for the rest everything works perfectly.
? ever happened to qualcuno??????????

[passion engines]

so here today I wanted to write the scania r360 but when I open the software of the cock I have seen that is not seen pi? the list of trucks,tractors, and motorcycles for the rest everything works perfectly.

[alien78]

ok, thanks a lot passion engines today I try and let you know

[nox]

Go quiet as you said angel redo everything and the shore I recommend if ? the version with the date back and forgive even those that already? ? happened to me too

[Mr.Flash]

what does it mean **** c'? a word that you can't? say ?

[passion engines]

Hello maybe I was wrong to type I meant to make a new installation from the sw content in the dvd

[Mr.Flash]

in the sense of your sentence there is the word "c.a.p.or." without dots for? if you write "****" come out four asterisks , I do not know why? perhaps an error of the forum

[leandro89]

there are words that are automatically corrected, nothing to worry about, obviously, will be banned, simple as that!!!!

[alien78]

anyway thanks to all, especially to the passion motors the cock ? back to life.....................

[Mr.Flash]

there are words that are automatically corrected, nothing to worry about, obviously, will be banned, simple as that!!!!

well it all ? relative leandro ...... also consider the simple fact that to write a simple word like d.a.c.c.a.p.or. ? must use the points to get this: dac**** :) ? obvious that is prohibited , what you do not understand ? why?..... clearly ? "pour parler" , to me it's good also cos?, nothing polemical, I wish to emphasise.

[sno74]

It was already been said in other posts that the word C. A. P. O. is obscured for reasons that have arisen from the old esperoenze of the forum....

[nox]

Vabbene regardless of the or.t are you able to write?

[leandro89]

Vabbene regardless of the or.t are you able to write?

quoto nox we avoid the whole discussion when there is need, we maintain active the object of the discussion.

[kingsnake]

I ? was asked to read a volvo fh, only that I fear to connect to the obd, in the worst case what is the risk of frying?

[nox]

In reading anything if you use the v53 for? eye on some truk you have to delete the adapter with the yellow behind the cock

[kingsnake]

Thanks for the information, as the owner calls me to read it and you say? how it will finish.

[davidehfnos]

it seems strange to me that with the clone you are working in 24v

[nox]

I, up until now, I only read for the tests. Daf xf. Iveco eutotech cursor scania r500 and 360 for? I failed on eurocargo edc7

[davidehfnos]

with the v53?

[cinqueturbo]

The thing that intrigues me and that's it? it is in BDM these ECU are powered at 12v and not 24v..

[nox]

You v53. And the cursor even with the 48

[sisco]

The thing that intrigues me and that's it? it is in BDM these ECU are powered at 12v and not 24v..
I when I read in bdm a s6 scania with gallo v. 84 I powered up the ecu to 24 volts when on pdf fgtech c'? written 12 volts (I have considered it an error)? the cock was powered by a 12 volt priority watch? then again, I didn't know if she could go to a24

[robby51039]

hi has anyone ever read scania 124 420 control unit ms6.2 with cock v50? I yesterday I tried but it did not give me even ecu data , it gave me an error message of"wake up"in the connection.will u error in the software, or the interface?
or just not read the serial?
has anyone tried it?

[sisco]

hello robby, I can assure you that your serial is the law, and I have read several with the rooster version 48 or (84 as I get up in the screenshot)? at the beginning do not read even then, I've done the mod of the resistance 3.9 khom and I have read and written.greetings

[robby51039]

do you have a photo that indicates the resistance to be replaced??

anyway my cock is laversione 50 that works in the bdm for now, has always done her job well, according to you and the changes that were made at the time?

[sisco]

do you have a photo that indicates the resistance to be replaced??

hello robby also my when in serial't read in bdm worked great I can assure you that after the mod the only resistance from 10 khom with a 3.9 khom began to read the ms6.2 for? still gave some problems on some edc 15 then I have also replaced the resistors that were not right which are mounted near a rel?, cos? ? further improved, up to now I have read 35 ecu ms6.2 of these for? 2 have withstood not? why?.
I'll send you a pic with the mod made by another user of the forum cos? you can check the resistance, if I can give you a tip if you have to change you first and 10 with a 3.9 and then first try to change the other,hello and happy easter

[robby51039]

thanks a lot of the council now unmount and control as in the photo,the strange thing is that, until now, my cock is always behaved well with both edc 15 bdm and boot edc17 tricore
and edc 16,the precise in addition to a daily, always with boschms and the first truck that I try to read

thanks a lot of the council now unmount and control as in the photo,the strange thing is that, until now, my cock is always behaved well with both edc 15 bdm and boot edc17 tricore
and edc 16,the precise in addition to a daily, always with boschms and the first truck that I try to read

[sisco]

to me is the daily read for? was ms 6.3, be careful, check that it is really a 420 with the ms6.2 why? there are some with the ecu motorola s6 and the ones you read on the can as you can see from the pdf in the folder of the cock, in the last you should also try on another vehicle with the ms6.2 in order to be certain that the problem is on the tool and not on the vehicle scania 4 series 480 and 580 also they are ms6.2

[robby51039]

then my tool up to now never had a problem, however, I tried to read with the protocol motorola but it gave me the same problem.
my application is slightly different than the one posted in the picture it is the one with a yellow led and changes the layout of a 10kohm resistor

anyway tomorrow I will try to read the cursor with the ms6.2 and see how it behaves

for sisco,then I tried to see the resistance on the inside and are a little different,I need to know how it is named on the inside of your tool because' my' to a led.
it should be the r27 or r28,can you give me an eye?
I tried to read cursor but it gave me the same error surely do I need to replace the resistors

r27 and r28 should be the one to be replaced with a 3.9 kohm

[sisco]

then my tool up to now never had a problem, however, I tried to read with the protocol motorola but it gave me the same problem.
my application is slightly different than the one posted in the picture it is the one with a yellow led and changes the layout of a 10kohm resistor

anyway tomorrow I will try to read the cursor with the ms6.2 and see how it behaves

for sisco,then I tried to see the resistance on the inside and are a little different,I need to know how it is named on the inside of your tool because' my' to a led.
it should be the r27 or r28,can you give me an eye?
I tried to read cursor but it gave me the same error surely do I need to replace the resistors

r27 and r28 should be the one to be replaced with a 3.9 kohm

hello robby, you need to have a p? patience why? I'm not at home but I have the tool with me when I get a moment I'll open it and let you know
however, to be replaced by put 3.9 khom ? one hello

[sisco]

hello robby I am sending you 2 pictures, one ? the resistance 3.9 khom where ? placed in my tool? near r 27) the others are the other 2 (of a group of 4) that I replaced in my tool, don't ask for the value now, why? I don't remember exactly.
if your tool c'? 10 khom in place of the 3.9 and after having replaced still not v? are you also looking for the value of those other 4 resistors

[robby51039]

I'll send you a photo of my tool to understand where I have the problem I have indicated what I assume are the resistors you will notice that they are arranged in such a way diverso7739

[sisco]

hello robby, I see that your ? quite a bit different, I suggest to measure with the multimeter the value of those two resistors (r 27 and r 28) and see if anyone of the forum that has a tool like yours, it says the value is in its tool, in my not able to understand which numbers have given the resistance I'm talking about, near you see r28 (that big blue) so it might be r27 that 3.9 khom?

[robby51039]

no, I think that a large resistance is the R63 while the resistance which I assume is to change both the r28,have you noticed that in my numbering of the resistors above the relays are not in a row, but they must be in sequence 54 57 55 56?
strange as true as I take as reference to see if they are ok?

[sisco]

if, according to you ? the r-28 and measure at least to know how ?, then for those close to the rel? search of winning back the first photos I sent you some ? hard given that they are not numbered to? maybe also measuring those maybe you can locate some position

[robby51039]

today I tried to read the scania after replacing the resistor, which I assumed was right, of course, is not successful.
there is no one who has ever read with cock v50 1 led?
if someone has never done any modifications on this cock?

[passion engines]

Hello robby, the title of this post speaks of a different version and not yours, I believe that if you do a search in the forum ? full of info that speak to the mod of your version....