Siemens SID 806 and the Cock V50

[Driver]

Hello to all. Should I read a siemens sid 806 Citroen C2 1.4 HDI 68 Hp. I saw that in the list the CAR under such control unit, can you? do the ECU ID and write it but not the you can? read. Andoando section boot mode c'? precisely the reading through boot. The problem ? that I did not go back the connection of the wires from the diagram that they provide you with the wing nut for the sid 806. I have to use the blue wire for the K line? And then according to that scheme, there are only supplies direct + 12V! Can?

Thanks to those who help you. :)

[nox]

The k line and the green wire . The mass there must stands for strength!

[Driver]

Ok, the mass was understood that there was, in my doubt ? that I did not see any power switch and m i seemed strange. Anyway I have already? tried to connect it as shown in the diagram but doesn't want to read it!!! Probably ? own the K-line of my cock that does not go as gi? I suspected. :rolleyes:

[nox]

The distribution you do with the switch that is on the cable if nn open nn works check with a tester when ? access or when ? off

In addition to now I don't know if you have already? the experience of reading in the boot but if you could maintain the mass in the boot well you will never look

[motorsport]

This is in the boot of the wire and the gray is the k line and the green 2 positive and a ground plane,or you can write it down with the mag for? we will not recommend you,you must nourish it from the cable and you have to have the on/off switch in the box,or off the flasks should have onboard an AM29f400!! :)

[Driver]

Thanks for the replies guys! You knew of the boot, in fact I had already? open and as you rightly said motorsport mounts a AM29F400BB. The switch I have it and I had fed, but I thought there were more feeds. At this point I think it's really the cock... as soon as I make the change to the rooster try again and I want to know!!! :)

While writing it I can do it in the obd via CAN line up with the cock??

[motorsport]

you can write it by obd for? read it first in the boot for pararti the buttocks,then if it does not read the k line, you'll find a post about it for the mod k-line!!

[Driver]

It, but had problems on the K line I was sure of almost 99% and this ? was the confirmation. I have already? read the discussion about the mod and in the week I can fix it (Hopefully). Definitely make? a copy of the boot. I'll keep you updated. Thanks.

[legendaryslave]

I would recommend you try the k on another type of ecu these are notes why? he does not like to be read, I take it? lost hope when they come to the dissaldo directly

[Driver]

Definitely prover? also other control units, but I do not read nor do the EDC15!!! :(

[nox]

The important thing, and what you do well the various steps ! Then, if you are sure you have made them ok then, I'm at the point and just the cock

[Driver]

[motorsport]

Definitely prover? also other control units, but I do not read nor do the EDC15!!! :(
you see that your chicken just the k line is wrong,now fix it for the holidays!! :)

[Driver]

I'm back, after several peripezzie I opted for a cock V53.

I finally read the ecu without problems in boot mode. The resulting file ? a file from 512 Kb to? by uploading it in titanium I do not find the driver can?

[cinqueturbo]

I'm back, after several peripezzie I opted for a cock V53.

I finally read the ecu without problems in boot mode. The resulting file ? a file from 512 Kb to? by uploading it in titanium I do not find the driver can?




In the info I find these data:
Siemens
Diesel Common Rail
5WS40285C-T
Num HW: 9660300280
Num SW: 9653451880
SID806
S122812002A
S122812002Z
S122827001A
S122829003A
CAPN2410.DAT
select you the driver...

[Driver]