Map Leon Cupra 240Cv

[pippox]

Hello all, I was made to map the machine to a professional and see what was written on the site, the machine would have to earn more than 40 horses
The problem is that you can taste the difference but I am not convinced that the 40cv or more there are much more that the other one is that I have no benchmark for comparison, so I would like to if there is any pious soul, that you may give a look at the map to see if the map may or may not give the promised gain.
Thank you in advance

[magi1984]

I am not an expert but I personally do not like
you touched on the parameters relating to the turbine,changing all the correction maps turbo pressure, temperature, air, etc., maps and personally, I would not have touched...I would have just changed the pressure limiter turbo, he gave a maximum increase of 25%, I would have given a p? less

in addition, he has not touched the throttle angle and engine torque,and has touched the torque limiter while the rev-limiter has touched only 1 out of 4
you edited a map that ecm titanium calls injection base map, that map when I did the course have told me not to modify it unless the vehicle has no mechanical changes

I repeat, I do not like it...I leave the word to the experts

[pippox]

Thank you very much for your analysis, but what I would like to know is if you think this map might give you the gain that has promised me, then from what I read you have open with ecm titanium right?
Because I have tried to open it with ecm titanium 1.61 but I cannot open because I have a driver but it is not compatible with the version that I have. Not that you could give me the driver that you used you?

[msport (exil77grande)]

Thank you very much for your analysis, but what I would like to know is if you think this map might give you the gain that has promised me, then from what I read you have open with ecm titanium right?
Because I have tried to open it with ecm titanium 1.61 but I cannot open because I have a driver but it is not compatible with the version that I have. Not that you could give me the driver that you used you?

even if he can not give you the driver because, however, would not work,the titanium is not the same as the ecm 2001,in addition to his driver as my it works perfectly because it's the official version.

[magi1984]

exactly...even if not funzioneebbe the driver on the official version designed
for me, you have not earned 40cv, for? the only way of knowing ? put it on a test bench power

[pippox]

exactly...even if not funzioneebbe the driver on the official version designed
for me, you have not earned 40cv, for? the only way of knowing ? put it on a test bench power

I have analyzed the structure of the driver, and I can assure you that having the updated driver also works on the version edited because the driver is a table with the references.
However, I understand, of course, you've paid for, and not even I would give around to the first one that happens, I'm allowed to ask this only because I thought I had a version of "cured"

[magi1984]

no perhaps you don't understand...not ? a question of wanting or not wanting to go to the original driver
what you say is not ? feasible,the original driver is not working on sw crakkato, otherwise they would have already? all
do you believe that I have not already? tried to do it?
the result ? just the same, that is, the file does not open

[msport (exil77grande)]

I have analyzed the structure of the driver, and I can assure you that having the updated driver also works on the version edited because the driver is a table with the references.
However, I understand, of course, you've paid for, and not even I would give around to the first one that happens, I'm allowed to ask this only because I thought I had a version of "cured"

I guarantee you that, here, we share everything and if maghi1984 not post it because it tastes like to me that you do, you'll do nothing of the driver,I've already done these tests with colleagues, and you definitely can not use drivers from other titanium original or crack.

[pippox]

Can I know which version do you have?

[magi1984]

the original version ? arrived at 1.67 I think.now I don't have the program open, but I think I remember well

[pippox]

Can I ask how big is your driver for the leon in bytes

[magi1984]

22 if I remember well

[gorimotors]

the original version ? arrived at 1.67 I think.now I don't have the program open, but I think I remember well

Yes, we are at 1.67

[pippox]

22 if I remember well

22 it is not possible. Could you kindly check?

[magi1984]

tomorrow check and let you know, now I am at home, and the SW original ? in the company

[pippox]

Ok, thanks a lot

[gorimotors]

However, the driver of the ECM is of little use, since most of the curves of management is located OUTSIDE the driver.

[magi1984]

however, I can confirm that the driver ? of 22kb

[matech]

Maps of the management, throttle, pedal, and engine torque have not been touched. Cos? as the advances of power.

The turbo pressure will have been touched just the various "fixes" but not the actual maps of management of the maximum pressure. Gi? then they are good compared to the version from 200cv then was not touching them...

I think if you study your map in comparison with that of the version to be 200cv you manage to get a result for the far better...

[matech]

and without the driver :-)

[cawadany]

Maps of the management, throttle, pedal, and engine torque have not been touched. Cos? as the advances of power.

The turbo pressure will have been touched just the various "fixes" but not the actual maps of management of the maximum pressure. Gi? then they are good compared to the version from 200cv then was not touching them...

I think if you study your map in comparison with that of the version to be 200cv you manage to get a result for the far better...

Advances are not to touch for the force according to me.... indeed, c'? to do mooolta attention, you are likely to do serious damage.....

[matech]

some degree of advance at low loads, in the absence of a turbocharger, pi? increase the performance and decrease the fuel consumption...

[gorimotors]

On such a map the advances are the last thing to touch... First you need to think about dealing with the turbo and injection, what's that ? been made even remotely on this mod. Then come the "subtleties"...

[cawadany]

Exact, leaving the advances on the same, you can get great results, on engines with a k04 then....

[mavaila1972]

Hello all, I was made to map the machine to a professional and see what was written on the site, the machine would have to earn more than 40 horses
The problem is that you can taste the difference but I am not convinced that the 40cv or more there are much more that the other one is that I have no benchmark for comparison, so I would like to if there is any pious soul, that you may give a look at the map to see if the map may or may not give the promised gain.
Thank you in advance

The last I see 40CV according to me it is not made a lot of good map

[mavaila1972]

On such a map the advances are the last thing to touch... First you need to think about dealing with the turbo and injection, what's that ? been made even remotely on this mod. Then come the "subtleties"...

I agree fully

[cawadany]

Surely not ? done well, otherwise Pippox would not even have had any doubt about the effective yield, given that that car with a map change from day to night.
With regard to advance payments, pay attention.... the results could be these :D

http://img607.imageshack.us/img607/1962/post9259074875600134476.jpg (http://imageshack.us/photo/my-images/607/post9259074875600134476.jpg/)

Uploaded with ImageShack.us http://imageshack.us)

[matech]

I have not spoken to in advance in phase of the turbocharger, in fact ;)

[cawadany]

I have not spoken to in advance in phase of the turbocharger, in fact ;)

Well, but not ? a turbo old style for this engine.... The turbine starts to push very low....

[pippox]

Thanks to all for the valuable analysis, but from what I read the map I do not seems to be made so well it is not that maybe it could be harmful?

[pippox]

however, I can confirm that the driver ? of 22kb

Thanks a lot very

[cawadany]

Thanks to all for the valuable analysis, but from what I read the map I do not seems to be made so well it is not that maybe it could be harmful?

Well, a "preparer" doing things cos? so much to do I would not trust, and to the point I lose the ori waiting to make a map worthy of the name.

[gorimotors]

Not ? harmful.. but not even performance

[cawadany]

In a certain sense better cos? then.... at least the damage will not do.....

[gorimotors]

[cawadany]

And wallets ;)

[pippox]

I don't know the exact harmful psychologically and to the portfolio because' I paid handsomely :mad:

[gorimotors]

Very often they do not ? the person the most? "known", or f? pay for the maps pi? of the other, s? remap really...

[cawadany]

Well look, I have a TDI too, and I've been there before you... Not that the map that I had not made it, but were touched of the parameters are not just cute, unbeknownst to me, of course. We will talk about 3 years ago, and unfortunately many things you knew.....

[giarras]

it is the latest version at the time 1.67 confirm.

[pippox]

no perhaps you don't understand...not ? a question of wanting or not wanting to go to the original driver
what you say is not ? feasible,the original driver is not working on sw crakkato, otherwise they would have already? all
do you believe that I have not already? tried to do it?
the result ? just the same, that is, the file does not open

I managed to find the way to load all the drivers including the one that would not open the leon in question, for now, the change is still in beta and I'm working on a permanent solution, however, both are convinced that the original or the less you can do, and the basic problem is that the version is 1.61, which runs has not been patched well

http://s9.postimage.org/gt9d2hlun/ecm.jpg

[magi1984]

congratulations! If you explain how you did it would be useful to all

[cawadany]

Very interesting!!!

[pippox]

For now I can correct the problem by modifying the driver and the database, and other values in the memory, but to do a thing well done I should be able to unzip the program and review the patch that was made, or to be able to have the version is not patched ecm 1.61, or you could start even from the most current version, if someone wants to make it available.

[msport (exil77grande)]

but could you explain step by step how to you correct?

[munro]

an advance on the benza pu? create detonation but c'? always the sensor that the piezoelectric ? in constant listening and a p? it cuts down on the advance ecessivo then from the image posted that the piston seems to be seized for excessive press turbo the advance eccesssivo to 90% of the cases you pit the pistons on the head

[pippox]

but could you explain step by step how to you correct?

Unfortunately, there is a standard procedure to follow some drivers have to be modified directly on the file, some on the database, and some will send into the infinite loop of the program, and those should be patched in memory
unfortunately, in this period I don't have much time, but I'm still working to find a permanent solution, which I will make available as soon as ready

[pippox]

I have modified the map studiandoci a little about it, and according to your valuable advice, according to you' as is'?

[pippox]

No one that I can look at this map? just to see if I made a caxx or not! :p