147 jtd edc15c7 start!

[eartip]

Then I read the original file of my car to tel a 147jtd 115 hp with ecu 15c7 below the original file:
file ori deleted

for now I just want to understand the process and I edited the file with ECM Titanium to linearize the system, the modified file ? the following:
6490

This last file if I open with ECM, I show the change properly after for? you have chosen to hand the driver.
I compared the two files with the utility of the ecm are different but have the same checksum 009.

I don ? clear if I can rewrite the file cos? com' ? with EOBD2 or if I should do the other steps...who is giving me a hand ?

the next step in this will be:
1) EGR
2), a light mapping

Thanks in advance

An admin if it can? correct me 157 147...thanks :rolleyes:

[leandro89]

Then I read the original file of my car to tel a 147jtd 115 hp with ecu 15c7 below the original file:
file ori deleted

for now I just want to understand the process and I edited the file with ECM Titanium to linearize the system, the modified file ? the following:
6490

This last file if I open with ECM, I show the change properly after for? you have chosen to hand the driver.
I compared the two files with the utility of the ecm are different but have the same checksum 009.

I don ? clear if I can rewrite the file cos? com' ? with EOBD2 or if I should do the other steps...who is giving me a hand ?

the next step in this will be:
1) EGR
2), a light mapping

Thanks in advance

An admin if it can? correct me 157 147...thanks :rolleyes:

the file ori should be inserted in the database if there were, and in the discussion it must be pasted the link with the number of posts

[eartip]

? gi? in the database
thanks for the correction
hello

[biondo83]

The checksum is calculated automatically from your serial programmer in the process of writing.

[nox]

But I do not think that if you are using the gall to write the correct the cks automatically cks is corrected automatically by edc16 ! On edc 15 I fix this before writing if you use mpps or hardware that allow you to or with ecm titanium if you have the driver. Once you save the mod file you correct him

[eartip]

...read using the gallo...
in the documentation of the ecm ? reported that if the driver ? this the cecksum ? calculated automatically

then scivo simply the file .MOD exported from the ECM???

[sportknight]

the ecm will find the driver?
if you find that when you save the file you must save the checksum is different!!

[eartip]

I find that when I read the original file...it is two to tell the truth : 15c7 488 and 490 15c7

then when I open the file .mod does not find it, but I have to specify it I ...so?

[biondo83]

On the EDC15c the checksum you automatically calculates your programmer Galletto serial OBD.
Tested several times.

Probably the software of management of my interface Galletto, the calcoler? in automatic. :-/

[eartip]

On the EDC15c the checksum you automatically calculates your programmer Galletto serial OBD.
Tested several times.
so I can flash my file .Mod directly ?

[nox]

It is normal that with the or you recognize the driver, and with the mod no ! The Ecm uses the cks to find the drivers. However, you put the ori select one of the two drivers that you find edit save eprom modified and re-enter safely with the cock I recommend no antivirus


On the EDC15c the checksum you automatically calculates your programmer Galletto serial OBD.
Tested several times.

Probably the software of management of my interface Galletto, the calcoler? in automatic. :-/



It is not me that he does not contraddirti ! And also I have 3 of cockerels

[eartip]

It is normal that with the or you recognize the driver, and with the mod no ! The Ecm uses the cks to find the drivers. However, you put the ori select one of the two drivers that you find edit save eprom modified and re-enter safely with the cock I recommend no antivirus

so I can prgrammare directly .The MOD that I posted right?

just to the sw of the cock I made a dedicated partition with xp not connected to the internet and no anti-virus :-)

[nox]

I'm with the phone I have no way to see the file now, however, if the proceder? you did and this is what I said, go quiet, it takes a minute to write me then when I work on edc15 me I always do a read of the file ori with mpps ( so much for the things that it takes to read the edc15 it's worth)that on edc 15 and a bomb and raises many many times in the case of block !!!!

[eartip]

the file ori gi? bed and preserved .

in the case of block riprogammare bench right?

thanks

[nox]

You are right to keep it let's say that in the case of the block you reschedule to tour for? the flash in this case am29f400 and with programmer eprom for? as a gi? as I was telling you about .I always sbrogliata with mpps ( I speak always of edc15) those few times that to me ? nailed in writing with mpps after several attempts I shooting for? with the rooster v2 go quiet eye, even if it puts us very little to write, you should always put a booster on the batteries that it never hurts to let me know!

[eartip]

thanks..................

[frantik3]

The checksum is calculated automatically from your serial programmer in the process of writing.



I don't think any programmer automatically corrects the cecksum on edc15 foul manually

[eartip]

I have read that if the drivers are present in the ecm does it automatically now the situation ? this :
the original
Size: 524288 = 0x80000
Cks = 0x4BA1943
modified
Size: 524288 = 0x80000
Cks = 0x4BA2EFC

the same size and checksum is different.

How do you know when a checksum ? correct?

[nox]

It was not reported to you eartip ! If you did the driver go quiet

[eartip]

ok...Saturday morning I am dedicated to the programming in the meantime, I'm studying how to map :-)

[Already]

You have to use the driver 15c7 488.

[sportknight]

No programmer calculates the checksum on the edc15
The only easy way to calculate it ? the ecm, first load the gold, make search for the driver, and then edited on or uploaded to the mood, saved the job done and you can write

[eartip]

programmed without problems....EOBD2 notifies me for? that the families of the checksum is not ? this...
;-)