nero72

04-11-2013, 16:13

obd75

if you need to in an attempt to read it with the bdm100 you advance that you should not be able to read...
I say why? if you have the gallov2 the instructions are in the documents of the rooster..

nero72

if you need to in an attempt to read it with the bdm100 you advance that you should not be able to read...
I say why? if you have the gallov2 the instructions are in the documents of the rooster..

You've seen the manual, but I wanted to know the pin 1, what corresponds to the pin 2 to what else, and so on, i.e. pin 1 to 3.3 volts pin 2 to vdd (? an example of this ), then reading I did not understand whether to enter the e xxx that reverses the flat, if you give me an explanation of pi? detailed it will be? grateful.Thanks a lot, Gianfranco.

I forgot the cock v2 then I should be able to read.

obd75

I haven't done these ecu,once she turned up, but still had the gall v2.
I can tell you about us? what I would do: connect the output of the rooster, we have ground to pin 5-3 show with the e xxx, where you v? to fall back the gruond and see where there is mass in the connections bdm ecu cos? you should understand the way as going to solder the e xxx I hope I was clear...

cinqueturbo

04-11-2013, 19:12

since no requirements to download or view attachments, I suggest you do a search on ******..

however, this would be the pin out right..

nero72

Ok OBD75, this check is made, or the side that the pin 3 and pin 5 is located, and then putting the e xxx from siemens, you should find it all, in my opinion, are the resistances at the output bdm Thanks a lot, Gianfranco.

sportknight

nero72

OK, I read the manual, but it tells me only the pin nuemro 1 where it is located, but does not tell me the pin 1 what it refers to, I don't know if I have explained what I was looking for, something that will tell me the pin to what you refer. hello gianfranco.

cinqueturbo

OK, I read the manual, but it tells me only the pin nuemro 1 where it is located, but does not tell me the pin 1 what it refers to, I don't know if I have explained what I was looking for, something that will tell me the pin to what you refer. hello gianfranco.

or not understand where you see it I'm Pin1?

Pin G4 +12V
Pin C3 +12V
Pin H4-GND

cinqueturbo

or not understand where you see it I'm Pin1?

Pin G4 +12V
Pin C3 +12V
Pin H4-GND

Aaaa now or understood you speak of the pin1 of the e xxx!!
wow sorry...
eee and a problem you must understand from the orientation of the ECU..
how do I spegnartelo?
from the image of the manual jacks must be addressed to the t?..

obd75

05-11-2013, 19:23

in the schedule in correspondence with the pin 1 c'? a dot

carlo abarth

if you can be of help!!!!the read with the rooster 53!!!

carlo abarth

cinqueturbo

Perfect!! only that our friend obd75 could not? still see the attachments...
we would like another solution to show you the solution....

nero72

unfortunately I still have to wait a while for the photos, however, perhaps, and my cock v2 which is not to be reviewing, the output voltages I noticed a problem of voltage between pins 3 and 9 I do not have the 3.3 volts. thank you all for your helpfulness? greetings Gianfranco.

carlo abarth

the rules are the rules ...unfortunately I can not do otherwise!!!
Perfect!! only that our friend obd75 could not? still see the attachments...
we would like another solution to show you the solution....

sportknight

yesterday, however, I have struggled with a 204 land rover that they gave me...
I was not able to make it in the bdm...probably still will be? damaged the ecu