View The Full Version : edit elm 327
how to modify elm327 that f? whims can
for the pass contact in pm to the admin msport
Good morning, ? the same aregomento that I would like to treat ioo , purtroppocome new writing I do not have the privileges to read the file RAR.
In particular, I bought a elm 327 but I can not figure out where it must be inserted to read idati of my ecu iaw 4wf magneti marelli ,
kindly who I puoindicare indicate on which pin of the centrelina to be entered in the contacts ?
thanks in advance
Fulvio
bernardo943
17-09-2012, 15:17
but ? a software or hardware modification to do the jumpers and the elm ???
antonioantonio
14-11-2012, 13:10
but ? a software or hardware modification to do the jumpers and the elm ???
This is a change in hardware. You must first remove the corrosion resistance of 100 ohms between pin 6 and pin 14, then you must connect both pin 6 and the pin 14 to ground through a resistance of 100 ohms and a capacitor of 560 picofarad in the series. (see attached diagram)
bernardo943
14-11-2012, 19:23
This is a change in hardware. You must first remove the corrosion resistance of 100 ohms between pin 6 and pin 14, then you must connect both pin 6 and the pin 14 to ground through a resistance of 100 ohms and a capacitor of 560 picofarad in the series. (see attached diagram)
thanks a lot ;) but if I can't find the capacitor 560 pf can I take ir? great or pi? small ?
I apologize nuovamene why? the system tells me that I do not have the privileges to view the jpg file ? I have not earn credits?
thanks
Fulvio
The capacitors in general have an average tolerance that ranges from 5% to 10% , now I can't remember well in the business standard sold for the ability? in pf, but you can always put in parallel with a 470 pf with a 100 pf.
again I ask excuse not riusendo to open the images, I go for the idea : pins 6 and 14 must go connected together and in turn ill all be connected to ground through a resistor 100 hom and a capacitor 560 pf which are parallel between them, right ?
antonioantonio
15-11-2012, 15:12
If you go into an electronics store, capacitors 560 picofarad are easily found. Originally, the elm327 commonly sold on the internet have a resistance of 100 ohms between pins 6 and 14 (which then would be the pin that connect to the can bus of the car). You have to remove this resistor, and then connect separately to both the pin 6 pin 14 to ground through a resistance of 100 ohms and a capacitor 560 picofarad in series (one after the other). I hope I was clear.
msport (exil77grande)
15-11-2012, 19:32
I apologize nuovamene why? the system tells me that I do not have the privileges to view the jpg file ? I have not earn credits?
thanks
Fulvio
I invite you to read the rules, thanks.
Regulation read, thanks msport, even if I think he is a little restrictive but still fit myself.
antonioantonio
18-11-2012, 09:29
Regulation read, thanks msport, even if I think he is a little restrictive but still fit myself.
I confirm what is written, stating that before doing this you need to remove the resistance that c'? in the source between pin 6 and pin 14. Of course, these two pins will always remain connected to the can bus of the vehicle, the connection described (resistor and capacitor) andr? then, in parallel with the can line coming from the vehicle.
Hello guys sorry if I repeat the question, but I understand I like and what to do to change the ELM327, the CIO? WHAT TO BUY BETWEEN THE RESISTOR AND CAPACITOR, AND WHERE TO SOLDER, MAYBE IF C'? a pattern or picture to follow the steps to keep in mind that I am new to writing and I can not open any file, in any case, thanks to all
with this modification, that the privileges you would have?
I just opened my ELM327 Bluetooth ? already changed :))
Despite my elm327 is gi? changed.. when I try to log in to the service reset in the service, tells me it's not ? possible for an error with the elm327 interface. I noticed when doing the test of the interface through the options *********** tells me that this type of interface does not support any protocol type CAN. It is possible, in spite of the change..... ???
Many greetings
Thomas
I attach a couple of photos of my interface.
In the circuit from a face you notice the resistance r2 and the capacitor c2, the other side of the circuit the same components R1 and C1, as measured with the testesr resistance, and ? 100 ohm, and are connected, respectively, to the scheme of the amendment, to pin 4 and pin 6 connected to ground with a resistor and a capacitor in series. Why? it doesn't work ?
newsadapter
13-01-2013, 22:31
I change often elm327 and honestly I can never replace the resistors but I delete only, and so far all the versions that I changed to work perfectly without causing damage to the elm327 same and, above all, without causing damage to the ECU. Unfortunately I do not have system enough to see your attachments, but it will be? happy to help also for private messages. hello tuttiiiiiiiiiiiiiii
Hello I send you the photos so give me some advice :)
I elm I have to buy what you advise me who uses clearly appropriate to make this change, I thought I take the usb I fear that the Bluetooth I get in conflict with other tools that I always use Bluetooth.......
My ? bluetooth has never given me problems, then depends on how you use it, but the usb version ? the best.
does anyone know if you can install it on the tablet that has android as a system it would be a nice work ........
newsadapter
14-01-2013, 00:39
I elm I have to buy what you advise me who uses clearly appropriate to make this change, I thought I take the usb I fear that the Bluetooth I get in conflict with other tools that I always use Bluetooth.......
surely the usb interface ? better than bluetooth, even if you do not ? a recent version as the 1.5 goes well the same ;) ;) ;)...
of course, sometimes, it's not only the interface to connect to the control units, but often the diagnosis also requires the adapters as regards the fiat group, but if the brand of your car ? different then just the elm327 with a generic software such as digimoto, scanmaster, scan xl ect ect.
msport (exil77grande)
14-01-2013, 10:00
I see that our online store online not the c..... not even to every way I have deleted some post saw me and seemed a little rsipettono in our comparisons. https://www.professionalchiptuning.net/showthread.php?306-Diagnosi-Auto
newsadapter
14-01-2013, 10:08
I see that our online store online not the c..... not even to every way I have deleted some post saw me and seemed a little rsipettono in our comparisons. https://www.professionalchiptuning.net/showthread.php?306-Diagnosi-Auto
I apologize if I probably lack of respect for indicating the prices in the forum without having consulted your listini. not be repeated more.. ciaooo
ok then for the 3 adapters I need for the fiat, where to find them.... Then I can not buy it all together at the elm cos? I do ship everything at once......
does anyone know if you can install it on the tablet that has android as a system it would be a nice work ........
On Android you can install the app torque pro, very beautiful, useful and practical. The use and ? cool. Fiat Ecu Scan is not for Android, but only for windows mobile
sin was a nice solution, but with torque pro what we do with them I do not ever used....
we make the diagnosis, gates errors dtc, real-time controls the various parameters, and you can create a virtual dashboard where you see all the parameters in real time, believe me for a second mortgage, look for it on the internet and you will see..
not to mention that if you enter the right data in the machine will calculate through the OBD and GPS the couple and the horses theorists :)
nice but ? something that is expensive..... Do not post prices, just tell me if the game is worth the candle....
I think you can also find the original let's say you want to download. For the interface, I think it is enough a Elm327 classic
Is the game worth the candle.. anyway, the original cheap you can find it on the android market is also not the original :(
rondella72
28-02-2013, 00:08
Guys a elm 327 vers. 1.5 is able to work well with the multiecuscan?
Guys a elm 327 vers. 1.5 is able to work well with the multiecuscan?
washer,to be precise, there is no elm version 1.5, and only one found cinesina, that runs for a long time.
rondella72
28-02-2013, 13:30
washer,to be precise, there is no elm version 1.5, and only one found cinesina, that runs for a long time.
Thought so too, and thanks to you I had the confirmation, and these elm which would be the version?
Thought so too, and thanks to you I had the confirmation, and these elm which would be the version?
clone 1.3 original 1.4
with the clone.. not able to connect to the can line of the machine, with version 1.4 you don't have any problem.
rondella72
01-03-2013, 08:17
And for the clone if you can not connect you have to make changes, right?
And for the clone if you can not connect you have to make changes, right?
yes, but are you better already? buy the version is 1.4 so you do not have any type of problem.. and not have us any change
Sorry! ? possible to run elm with the software vag-com?
Even the 1.4 should be modified for problems on the can line, the 1.4 work, and why? they have been changed.
Little question... but this is changing hardware is only for the elm with a serial connection or applies to all models, including those the usb? no why? I have always used the 327 without major problems and without changes...
Little question... but this is changing hardware is only for the elm with a serial connection or applies to all models, including those the usb? no why? I have always used the 327 without major problems and without changes...
Even usb!
But if I buy the chip elm1.4 and the world where it was mounted l'1.2 do you think it works or I throw away the money
Even usb!
But if I buy the chip elm1.4 and the world where it was mounted l'1.2 do you think it works or I throw away the money
And how much is the chip? All the elm you buy new on the bay is also a 30 euro!
And how much is the chip? All the elm you buy new on the bay is also a 30 euro!
the chips aren't enough. it takes about 40€, for? ? original
minijuri
04-04-2013, 13:20
great thanks :)
I just bought the components, on a week end be? the change. Thanks
Xtreme0303
12-06-2013, 11:37
it also works on those bluetooth?
danny677
12-06-2013, 12:14
Even usb!
But if I buy the chip elm1.4 and the world where it was mounted l'1.2 do you think it works or I throw away the money
Do not throw your money but you get a elm updated to 1.4 original
can I know where you got them sorted?
I took them at an electronics store near home to 50 cent.
Guys I have a elm I I swichato pins 6-14 on 1-9 through a switch bipolar? now I find myself in this situation I have to say that I have a great point: with the switch from a start within the engine, electronics, central, abs, alignment, proxy and just while if I move the deviates from the other party does not within anywhere! Why? I would like to get in airbarg and service
danielecolantonio
20-10-2013, 19:13
guys I have purchased a elm recently, the open and took photos to the card. You say I can post the pictures so well? you tell me if it requires the change of the resistance?
MarcoG3092
25-11-2013, 07:40
I too have the ELM usb a bit of time, at the beginning did not work then I opened it and I deleted a resistance, as to the accuracy of the "R04", reinstalled everything and it worked... of course I had to take the adapter....
Guys I have a elm I I swichato pins 6-14 on 1-9 through a switch bipolar? now I find myself in this situation I have to say that I have a great point: with the switch from a start within the engine, electronics, central, abs, alignment, proxy and just while if I move the deviates from the other party does not within anywhere! Why? I would like to get in airbarg and service
Hello,
to put the deflectors to also have an interface type 3 ? a change that I want to do myself....
for your question I have noticed that there are different adapters depending on what you want to carry only the description why? for regolamanto you can not post the link:
*********** DIAGNOSTIC ADAPTOR SET SRS ABS :
The GREEN Adaptor allows you to cover ABS and Power Steering.
The RED Adaptor allows you to access the SRS (Airbags)
The YELLOW Adaptor allows low speed CAN BUS communication
You should know the difference of the connections between the three adaptors to be able to change the elm to read it all
Hello
marcusmagic
04-12-2013, 12:18
for giarras: you have disabled the messages in pm for all users, if one wants to ask for the pass to open the compressed folder as it should do?? so much to understand.. thank you..
msport (exil77grande)
04-12-2013, 15:13
for giarras: you have disabled the messages in pm for all users, if one wants to ask for the pass to open the compressed folder as it should do?? so much to understand.. thank you..
the pass you ask the admin,if you want to know how to ask for pass and' simple contact us via our ***** official.
SlimPickens
04-12-2013, 19:43
Guys I have a elm I I swichato pins 6-14 on 1-9 through a switch bipolar? now I find myself in this situation I have to say that I have a great point: with the switch from a start within the engine, electronics, central, abs, alignment, proxy and just while if I move the deviates from the other party does not within anywhere! Why? I would like to get in airbarg and service
Hello, I have done the same thing on two different interfaces. One of the two, in the mode? "service", has requested the removal of the resistance r04. Now it works, but well-known, however, that ? much more? slow in connection with respect to the other (they are "equal" but different).
hi sorry to disturb, I would like some clarification,I bought obd2 elm327 blothot, to use with the app torque pro, I have a fiat punto evo 1.3 diesel 75hp, this hardware works, everything or almost everything, that is, when I try errors tells me that does not find any errors,but my car comes out the signal of the failure airbeg, what should I do? I have to find another obd2 fit in my car? thanks
SlimPickens
06-12-2013, 21:41
It happens the same to me. With the laptop I notice occasionally an error that the phone does not detect, even if present. Also tried with another interface (I speak of the economy, but I don't think makes a difference in this case). So I think that is a problem, or better, a limitation of the software.
With elm and torque pro, make the diagnosis, to the engine control unit, and then hopefully find the only errors present in the engine control unit and the airbag or abs or body, etc.....
With elm and torque pro, make the diagnosis, to the engine control module, then eventually you will only find the faults in the engine control unit and not in the airbag or abs or body, etc.....if I wanted to find the errors airbeg etc., what you need to have a suitable software or another obd
SlimPickens
07-12-2013, 13:26
if I wanted to find errors also airbeg etc., what you need to have a suitable software or any other obd
I would say another software...
dreamc85
14-12-2013, 01:22
guys can you explain me better this thing of the chip v1.4 and v1.3 how do I distinguish them?
link deleted, for example, this would be complete?
or maybe should I buy this?
link deleted
thanks!
this ? the first is a call, I invite you to read the rules. I also remember that link de kind are prohibited by the regulation.
SlimPickens
14-12-2013, 14:13
Are updated versions of the integrated. Is always specified in the adverts. I have the 1.4 and for the little that I do I am fine. There is also 1.5 but I read that sometimes are not true, i.e. disassemble and you see that they are 1.2. However, it is enough to turn a reputable manufacturers, showing a good reliability
dreamc85
14-12-2013, 18:29
and are you able to access the airbag ecu, abs and power steering?
SlimPickens
14-12-2013, 18:31
You, with the appropriate adapters (as a response in the other discussion).
dreamc85
14-12-2013, 19:00
but this link deleted, you can mount them to the adapters?
Peppino91
14-12-2013, 19:42
but this link deleted, you can mount them to the adapters?
Not to break...for? I believe that the links do not them you should put...***** o buy the one with the cable and are you sure that you can mount.
dreamc85
14-12-2013, 20:00
ok sorry I read the escaped regulation and there I made the case!
Peppino91
14-12-2013, 20:04
aware that? gi? you have "recalled"
dreamc85
14-12-2013, 21:03
I have not received any recall... at least not that I noticed... can you tell me where I have been called back??
Peppino91
14-12-2013, 21:08
guys can you explain me better this thing of the chip v1.4 and v1.3 how do I distinguish them?
link deleted, for example, this would be complete?
or maybe should I buy this?
link deleted
thanks!
this ? the first is a call, I invite you to read the rules. I also remember that link de kind are prohibited by the regulation.
here...a couple of messages before ;)
net_proo
11-03-2014, 18:28
hello,
version witch elm 1.4 or 1.5 pu? be amended?
alfonsoh
22-05-2014, 14:42
hello, I wanted to ask for the change need to? I have a elm 1,3 I have a problem with multiecuscan and connection to the paintings and the electronics of the outside of one of the engine, while still having the adapters right I can not in communication, the need for the case to resolve that problem?
MarcoG3092
22-05-2014, 16:42
Eliminates the resistance R04 and you'll see that it connects.
alfonsoh
22-05-2014, 20:31
I will try thanks
Hi I have a elm327 ver 1.5 how do I connect to the engine xke nn connect
Hello,
first of all that car talk and what are you trying to do?
Hello Elmino,
I have a GP and on my ELM327 1.5 a I had to delete a terminating resistor... 120 OHMS, which puts you between CANH and CANL
Unmount the ELM 327 and pulls the card out of the.... I in the meantime, I will take a photo of the point where I've taken off the resistance I
PS: I Had the same problem... not connettevaed andavain error.
Hello
Hello Elmino,
I have a GP and on my ELM327 1.5 a I had to delete a terminating resistor... 120 OHMS, which puts you between CANH and CANL
Unmount the ELM 327 and pulls the card out of the.... I in the meantime, I will take a photo of the point where I've taken off the resistance I
PS: I Had the same problem... not connettevaed andavain error.
Hello
Hello thank you...to then see the image that places like I do? I thank you in advance
You are right... post pictures of your card and I'll tell you what you need to change...
otherwise you have to wait quite a bit.... :-(
You are right... post pictures of your card and I'll tell you what you need to change...
Cia, I also have a ELM 327 v. 1.5 (a) (before I had a 1.4 modified, but this is totally different).
Version-U03AJ_M "1.5"
dated 2016-05-16 (I found the same initials on another forum but the previous version had the numbers of the resistors, not mine, and parity of the acronym on the board, is willing whit)
This does not work, does not connect to the... is not recognized... the cd driver is useless.
Cia, I also have a ELM 327 v. 1.5 (a) (before I had a 1.4 modified, but this is totally different).
Version-U03AJ_M "1.5"
dated 2016-05-16 (I found the same initials on another forum but the previous version had the numbers of the resistors, not mine, and parity of the acronym on the board, is willing whit)
This does not work, does not connect to the... is not recognized... the cd driver is useless.
what you describe is a driver issue of windows...
elmino follow the tracks of CANH CANL on the card, resistance to be removed is located between these two lines
on resistance, there is written, 121, that would be 120ohm
Powered by vBulletin® Version 4.2.2 Copyright © 2025 vBulletin Solutions, Inc. All rights reserved.