View The Full Version : Heeeellllppppp! Scodifica Partial Or Total Bosch Edc16C3 Pegeout 206Hdi
Hi I would like help on scodifica a bosch edc16c3 pegeout 206 hdi since yesterday trying bdm with bdm100 galletto v2 are not able to be able to read the entire file to the scodifica.Some of you would be cos? nice to be able to help? Thank you and I am attaching the photos of the ecu.
you have to have the content of 95160 if not the law in bdm off the ep2 and read it with a programmer and e-mail the file I don't know if this ecu you can have the total.....
but in the bdm with the gallo2 the recognized? what you have read.
you have to have the content of 95160 if not the law in bdm off the ep2 and read it with a programmer and e-mail the file I don't know if this ecu you can have the total.....
on psa is not ? can the total, I have tried it with the assistance of a person of the craft without success, only partial
Guys thanks to all for the answer, but certainly today prover? to do the partial via programmer william detaching the micro-95160 and I want to know, but someone of you has ever done?
Total nothing,post the contents of 95160 the partial ago with no problems!!
on psa is not ? can the total, I have tried it with the assistance of a person of the craft without success, only partial
Hello Ivan
If you can do it with no problem, done it many times, edc16c3 & edc16c34 psa.
Hello Ivan
If you can do it with no problem, done it many times, edc16c3 & edc16c34 psa.
but you do it with ep2 or serves emulator......
hello gezame explain to us the solution for the total? grz
but you do it with ep2 or serves emulator......
Hello
From ep2.
ok but use a sw or do you have a database for these files to be used for total...
Hello
It is manual, in the dump original to the car.
but that area, you must edit the dump you have an example for us to understand....
Hello
Some of the software is the same, but just reading and tamano exact.
If you read in the bdm, normally, you have to do by hand.
Hello
Some of the software is the same, but just reading and tamano exact.
If you read in the bdm, normally, you have to do by hand.
Hello gezame listen to a thing you may edit the file that I posted at the beginning so total? I dissaltato the chip 95160 place in the back of the ecu and using willem programmer by selecting mode? writing I have written the e2p partial to me ? was made and now I have yet to try it.The strange thing to me ? been told
That for it to total the edc16c3 there was need of an emulator, so I have made the parziale............Now given that you're saying that really can you? make total you could make me mode? total??? I would be really grateful thanks........
Sorry again I have to post the file anyway the e2p of the 95160 I modified it with software car software ? I modified it and then the scritta..............
but I have seen carsoft 5.2 non c'? this ecu what did you use to make the file.....
but I have seen carsoft 5.2 non c'? this ecu what did you use to make the file.....
I have used car software 5.0 and anyway, there is checks good then nn I
I carsoft I view this page.....
I carsoft I view this page.....
Well if you're using one of the pegeout bosch edc16c34 total 1400 69 hp should work
Well if you're using one of the pegeout bosch edc16c34 total 1400 69 hp should work
you worked?
but I also don't understand your ecu ? a 16C3 HDI uses a 16c39 in fact it has not worked I on the other sw I saw that 16c3 only partial... for the total you have yet to figure out how to do it from ep2 you were talking about in the post, is a method of procedure manual in the mail file that you have read that let's see if someone helps you......
is total without problems,on some it does not exceed the 3000giri,but with a jumper in the bsi it's all ok..
sorry SGHERRY let us see this bridge that we are curious,some photos or pins to connect!! grz
some that call the ecu control unit for candles...... this I know that electronics can...... however it is better that you have solved......
Hello,tot is the eprom,you'll see that in the bsi a rele'starts on and off...missing the 15!!c34 nn goes well, the injection system is different,also, but beating up bad,it's good only x proof.
then you can make total.... if only to turn on you don't need much......
hello,on the 16c3, and is working 100%,and on the 16c34 that it's okay to only the x test....
I will resume this discussion can have a solution immoff on this ecu EDC16C3 Peugeot 307 1.4 HDI place ep2
It is a peugeot doing
On ford/mazda no...have a rollin code
I the file I did the machine part but remains cut at 3000 rpm............
Is it possible to have more precise directions, or do I have to find the schema of the BSI, thanks......
In the bsi
Missing a 15
can I have more info thanks
my friend in this kind of ecu if you make immo off to the eeprom, the car start but went to the limp mode cant exceed 3000 TR I know i have a complet bdm mpc flash eeprom to inject and have the full power of the car and immo off i will posted here because the immo fuction not only in the eeprom but in flash too advanced psa ecu like edc16C34 there is no problem just the eeprom immo off and car ok
Powered by vBulletin® Version 4.2.2 Copyright © 2025 vBulletin Solutions, Inc. All rights reserved.