Already

Hi
I have to scodificare a iaw 16f.
Not having the interface, I Would like to try to read the motorola 68hc11 and process the file using software such as the telephone or immokiller.
Has anyone used this procedure? does it work?

Any advice? I can not do the procedure clock why? I don't have the car.
Advice?
Thanks

alex68

mandamela you do it no problem

glittering chiffon party dress.fitted

Certainly I am attaching the procedure hello

Already

Thanks for the reply! of course, if you don't link the immo make the total?

Another doubt I will. As ever, from the photos, the food, the ecu?

glittering chiffon party dress.fitted

16-09-2013, 18:20

Of course, you must disconnect the immo to the total, you'll find it above the fuse box for the power supply to the ecu I have a dedicated interface, and I don't follow this procedure ,a colleague of mine who does not have the interface you ? amused to complete this beautiful work, and I think that the power on the ecu is not obligatory, maybe he wanted to work with certainty not deafening nothing you can do the same thing hello.

glittering chiffon party dress.fitted

Sorry if I omitted the connections to the ecu,if they were to use pin 34 negative, pin 35 and 26 positive

Already

What can I say! thanks a lot and good make

Already

16-09-2013, 23:48

I tried to read the micro-x prog. It tells me the device Is silent. Who wants to say. The links are ok

glittering chiffon party dress.fitted

I don't use xprog but I know that should read this micro,have you tried to power the ecu and not hello.

Already

You!
among the many attempts that I have made, at a certain point he started to funzionatr, but he read an empty file (all ff), and also, if you write something, you do not write anything

glittering chiffon party dress.fitted

Pin 9 of the micro I imagine that the instructions you have not plugged in and that you have not made a mistake in the choice of the micro-to-read, with the upa my friend has not had any problems in any case, if you want I can send the ecu you only pay for the transport to the scodifica you do it for free hello let me know

Already

17-09-2013, 14:05

Thank you so much for the availability, but I wanted to try ( and maybe succeed ) I.

The pin 9, you have to raise. I connect it as he tells me the manual of the x-prog

glittering chiffon party dress.fitted

The exact hello and good job

giuseppe1374

from personal experience I can say that if you want to read with xprog do before I desolder

Already

I did the test to unsolder the micro, but nothing to do. When I do Read/ write always gives me the error. If I try more? times can you read a file incorrectly

passion engines

Already

You speak of the files of the clock? I hadn't thought about, but I don't trovavouna memoriaa available. This file is valid for all the 16f? They told me that it does not always work.

leandro89

thank youuuuuuuuuuuuuuuuuuuuuu
passes in the presentation section, first write in the discussions, as well? you know

sa80libero

make sure to check the links

sportknight

I explained that the instrument should be made of the scodifica?

mecdoc

I did the test to unsolder the micro, but nothing to do. When I do Read/ write always gives me the error. If I try more? times can you read a file incorrectly
but the oscillator will you put it?

Electric

I bought the interface and sw full of shoe do I do it without welding and without having to disassemble anything in 20 seconds ago total.

Already

but the oscillator will you put it?

it was just what my error

mindafuttu

But to be put on or off the oscillator?
I have a similar problem with the mcu mc68hc08az32a, I don't understand where am I wrong.

alex68

But to be put on or off the oscillator?
I have a similar problem with the mcu mc68hc08az32a, I don't understand where am I wrong.
not go crazy if you send me you do I

mindafuttu

Thanks a lot alex68 x the availability, I solved it with the upa, but my question ?: as ever, both by the connections on the pcb by soldering the processor on the e xxx(without oscillator), I was not able to read the damn?

Mr.Flash

for these ecu c? a swap file, use a 27c512 with this file, the balances on the ecu then feeds the ecu for 30 seconds dissaldi and re-mounting your original eprom, nothing more? the code you put only remove the lamp failure immo on the instrument panel

hello passion motors, I have seen your message and you would like to report this attachment that I added a little while ago , could you tell me if ? correct ? thanks in advance