Opinion Point map EVO 1600cc 120cv

[Tinturia]

Hello all,

I would like an opinion on the map in the annex.
I think it is not a bad map, and that does not create excessive stress to the engine... but I don't have an experience that you can be fully sure of there?.
According to you the maps that I have touched are right? There are others that I haven't considered?
My intent ? make a map with a good compromise fumosit?-power.

Needless to say that I accept any criticism.

[msport (exil77grande)]

the map is not too bad,certainly much better, but as a beginning, not bad,give it a try and you're already aware of the situation.

[Tinturia]

Thanks msport...your words encourage me!
I do not have the car available for issues of distances. I have requested the map as a result of luca stanca done long ago
Just try the map will try? to understand how to improve it based on the impressions of those who guide...sure to try it in person would be something else!!!

[dantesfx]

Thanks msport...your words encourage me!
I do not have the car available for issues of distances. I have requested the map as a result of luca stanca done long ago
Just try the map will try? to understand how to improve it based on the impressions of those who guide...sure to try it in person would be something else!!!

Of the difficulty? is often in the filter information received from clients, and "transform" into maps enjoyable, but not harmful.

[angelolsp]

the luca stanca what have you done?

[Tinturia]

The service file of the forum....you can try with ecusafe but without guarantees.

[explode82]

ecusafe according to me should not be on these,the time usually there are no problems even if on some cars can? give trouble

[angelolsp]

I will try both time ecusafe and x-spot advice in case

[eobdexpression]

I will try both time ecusafe and x-spot advice in case

In my opinion ecusafe it does not do well, and then you can try and with time only that, according to me, if I could do it manually it would be better to know the bits and the exact addresses

[fabiovts88]

excuse my ignorance but I have time I tried to close the egr and fap, but when I load the mod file that you saved from the time on the ecm 2001 I do not see the increases of the egr closed! as ever?

[neo]

As said msport there is still work to do.There are limiters IQ and rail pressure out drivers that have not been touched and much more.And another thing,have you deleted the Egr with Time however it is better that you leave only the two panetoni to 0, and restores ori l other 4 (addresses 1C982,1C69E8,1C6AB4,1C6B1A).If tomorrow I have a bit of time ****** I give you addresses for limiters out of driver, and look a little better even on the map.Hello.

[leandro89]

excuse my ignorance but I have time I tried to close the egr and fap, but when I load the mod file that you saved from the time on the ecm 2001 I do not see the increases of the egr closed! as ever?

this discussion is about an opinion the map, on the forum there is written how to see the changes, just look a little bit

[fabiovts88]

certain of this, but I wanted to know to know in advance the also here ? been used time as he did..

[leandro89]

certain of this, but I wanted to know to know in advance the also here ? been used time as he did..

yes, but you don't know how to see the differences, then your question is not ? appropriate to the discussion, on the site there are discussions that explain how to use the program and see the differences in 2d

[fabiovts88]

the differences of the egr closed I see them in 2d, but with my time it seems that nn change anything.. anyway you know me in the discussion?

[leandro89]

the differences of the egr closed I see them in 2d, but with my time it seems that nn change anything.. anyway you know me in the discussion?

then open a topic and write your problem

[fabiovts88]

ok thank you leandro