Opinion the map and info about the address Seat leon EDC15

[angelolsp]

Hi guys since I have to remove the crap of the map that I found on the car, I would try to make it I...I accept any criticism I have followed the reasoning of the mm3... I have not touched the maps fumes and map the pedal why? from the driver I wanted to understand something more?...

and then I would like at least in fo on these addresses..

0773CE?
04CEAA?
04D0FA limiters torque for gear? I have not touched since? they do not require the pi? of x 85mm3 now
04D354?
04D46C AND THE FOLLOWING...?
04E29A injection ? it seems the shape of the rail on the common rail..can be pressure pump here?
056142??
0567a0 map similar to 04E29A...
0573CE??
05B4E4?? AS EVER SO LONG?

[mikyrace82]

I'll help you so...

[angelolsp]

Thanks 1000 give a okkiata.delle changes that you think? I kpt something?

[angelolsp]

I gave it a look...

[angelolsp]

instead, with regard to the maps pedal seen that until now I've used the driver, according to me, from the values that I get from the spins are reversed, can you confirm? :D

[angelolsp]

70 visits..don't I deserve a little help ??? :D

[angelolsp]

girls I need to know if and only if they mm3 or mg? can you tell me if no division by 0 and neglect the logic to do the tt team and do the increases in the percentage

[angelolsp]

[mikyrace82]

To calculate the duration in the PDE not ? difficult.The duration, have the first breakpoint, relating to the mg, and the second refers to the laps..Simple... the duration at constant rpm x vary the amount? the table values must be in the vertical, so if you want to reach the range of 70mg, change the last breakpoint, 55 and 60 with the values 60 and 70, then in the corresponding tables 60 mg the next to last line, in this case, copy all of the values of 100% and in the boxes of the horizontal 100%, seeing the differences of the last box, the values increase them multiply x2.Redo the map limiters fumes, doesn't it ? the one that the ecm called injection zoned. Breakpoints refer to the MAF, you may get them starting from the value 4500 about because if you close the egr and the MAF reading? a higher flow rate of air to a minimum.
The values should be if I'm not mistaken 13 parts from 4500 to get to the last box with a value of about 12000, which corresponds to 1200 mg vag x the maf. If you have a A/F 17 about the max load, ok.
I use a a/f at low loads of 18:1 until you get to the max of 17:1. The torque limiters of course you need to adapt them. The variable geometry, not keep it so closed, why? you will have an increase of the peak and an increase in the consumption of fuel. The map of pedal you could leave gold in the part that you have to 100% the value of 7000, and the lines below match (increasing values) up to 7000.... I hope is helpful for you...don't expect a map for free, it would not be right..

[angelolsp]

You don't want the map for free...inanxitutto thank you for your participation and aid..I just finished trying the map pushes well from 2500 up to 5300 but we can do better?? The limiter smoke then, and that map if I touched off the driver that I said that it seemed injection?? The launch control did not work could you tell me where I'm wrong??the last question you asked me to redo the map fumes but I am limiting myself in this mod don't get it to 75?? Thanks again

[mikyrace82]

then the smoke limiter ? that the long horizontal line that is located before the map that ecm called injection zoned...it should be up to 60mg ori...there is also another one after but you don't need to touch it... "sometimes" the ecm is confusion...if you look at the map well injection zoned is not taken into account by the ecu..

with regard to the launch control have only sketched out, but you have not configured....for example, you did not put that speed? you should enter..

how many mg did you give her? the limiter fumes are not ? the map that ecm called injection zoned...the launch control will not work why? not ? set the number of laps, the speed? cut off and if as I think you have a manual transmission and not automatic or 4x4 not ? them that you need to act...

[angelolsp]

ok I understand what...I x I have now given not more than 75...but I can give you more than the car is fine but I would like more because x now smoke 0...I can get to 85 adapting limiters ccoppia and filer fumes always with this pressure, pear or not you agree?

[angelolsp]

one other thing I wanted to ask the machine before 5000 arrived at the limiter ...now pull the 5300 does not go down, but I feel it shoot...to get it to 5500 and let it shoot I have to raise a 2-d torque limiters and the wide choice in acceleration but km can I take your 5500 not having the driver who tells me this? and a question, maybe stupid, but I'm afraid to damage, going beyond the 5500 thanks again :)

[mikyrace82]

what software do you use? if you shoot maybe why? do you have a line of surge protectors that tends to "blend" and it is not falling...or arrivals light limiter...75mg as it should with about 1.7 bar, you should stay around 190cv..

[angelolsp]

Use ecm titanium tomorrow settle better then 75 just do not Go beyond tomorrow...as soon as I finish if you can look at it and tell me ke you think and if I Arrive at 5500 and let it shoot and then I would like to focus on the launch control thanks again :)

[mikyrace82]

also the 5200 bastano...su an original engine have been sufficient...

[angelolsp]

[angelolsp]

I adjusted all o6e402 and the other limiters fumes ke you said ke no need to touch it? after that the map in the ladder in which I gave a 10 x cents... so are at 75 mg how does it sound? we arrive to the 5500 and let it shoot? :)

[mikyrace82]

the first horror ? the map "enrichment in the acc," you have points in the negative, the requests below the map ori, and a request to max rpm/load that exceeds that of the limiters and the map smoke.. You started to change it when the engine ? still off... ...the limiters torque I don't like up to the 2500giri..one of which is the fact waning...o6e402 not ? a limiter fumes..turbo pressure is not adequate to the demand diesel...missing the maps, the diesel with its breakpoint. I would say that the first to point it at 80mg you should clarify a lot of things..

[angelolsp]

sorry you are right, but when I saved the file I don't know kosa has combined the ecm would take a picture and put away immediately

[angelolsp]

ok so, and that is how I wanted it...with regard to the press turbo I don't want to go up again...because it's a turbine golds and already ki l had mapped before, he had given 255 points so it was high...150 not enough?

[angelolsp]

the l?impersonators, as a couple, should I get them?

[angelolsp]

I don't understand me and crazy ecm...

[mikyrace82]

first of all try to change it using the 2d and more? linear..not to save the changes on similar maps but work one at a time...the ecm is often the tantrums...

[angelolsp]

ok thanks...will try? so about the map that you tell me also if there are errors in the ecm, I think the base l have it...

[angelolsp]

ok perfect, put it all in 2d, and nothing changes in the most part of the ecm, I have also seen increases, and I solved it now eas it?

[mikyrace82]

this ? a base on which you can continue...L_C activated.

[angelolsp]

I don't know how to thank you tomorrow hi an interview in a workshop just rienteo hoping for the best control of all thanks again :)

[dvdtuning]

Angel, but the launch control worked?

[angelolsp]

I'm waiting for the clutch and then I write lamappa comunqueve configured correctly, I wanted to ask soko if I had to recopy saw ke each map has a copy

[dvdtuning]

today I tried the same map on the golf 4 1.9 130hp edc15p and should not be.

[angelolsp]

attention to set it up myself, I made a mistake the first time but now mikyrace the adjusted

[angelolsp]

If you have configured how did mikyrace try to copy also the related...let me know

[dvdtuning]

here is ori and mod.

[angelolsp]

then you have configured it as up to me with -24,7 but you have not done + 6,8

[angelolsp]

check best done by mikyrace....sorry for the double message

[dvdtuning]

Always in the area of the limiting speed?

[angelolsp]

It is exactly immediately prior to the increase in negative 24.7 just before, if you look at my c and a positive increase of 6.8

[voglioimparare]

nice discussion guys,congratulations !soon as I get the chance? to download attachments, I would like to read also I the guide posted.make a map with the policy, and one thing,make it a case or without cognition, and another!

[angelolsp]

We must say a big thank you mikyrace gave me some tips :)

[dvdtuning]

We must say a big thank you mikyrace gave me some tips :)

now it seems to me correct, but still does not work.

[angelolsp]

now and done right perhaps the panettone has been reset to zero before my...sq km or try to copy l similar 05c5d6 and after 0659a let me know why it affects me too...

[munro]

guys, the launch control is activated moddando a map only by 25x14 where the axes, respectively, there are
X:rpm
Y:vehicle speed in km 0 to 44
Z:iq calibrated everything is 100 mg
e.g in BP relative to 0 km, starting from where you want to intervene in the LC e.g. 2500 rpm
you set a iq nothing in the z-axis of that? 0 mg for the whole of the horizontal line up to 5361 rpm....
the same you can? do to the BP relative to the other speed? right where you want the LC to intervene....
by tapping over that way you f? only a papocchio according to me...

[angelolsp]

I am on the net I found the screen and mikyrace has taught me how to set it up you, how would you do it?

[dvdtuning]

So you mean moddare only the limiter gear without acting on brack point...

[angelolsp]

but moddando only limiters how do you set the entry and the exit of the launch control? dvdtuning l have you tried to copy him in all similar I read on the net that one did not work because I do not had copied in all the related and after it worked to you and how did that go?

[munro]

I am on the net I found the screen and mikyrace has taught me how to set it up you, how would you do it?
exactly as I described...
prior to? you have to find the map 25x14.....

[angelolsp]

then I made the launch control through vagsuite setting it to 2550 and recognizable 6.3 km/h...after you have saved the file, I open the file in 2d with ecm and me in order to reset the panettone limitation without any additional tap the break point as said tuning dvd...now I don't know if it works, I have no way to try it x now dvd tuning if you imposed your you have tried it?

[angelolsp]

exactly as I described...
prior to? you have to find the map 25x14.....
map 25 x 14, and this

[angelolsp]

watching it in 2d but I have a small straight line just to 2550 and I figured out how to see the 6.3 km/h in 2d or better speed because 6,3 l I and set I...

[angelolsp]

try dvd tuning...you have to calculate the cks let me know :)

[dvdtuning]

Now I do not have more? the car...as soon as I can try again.

[mikyrace82]

sometimes if it doesn't work ? why? you have to take care where you make the launch...if ? 4x4, automatic or manual

[mikyrace82]

now it seems to me correct, but still does not work.
no, no ? correct..example..laps, where he worked on the launch?

[mikyrace82]

try dvd tuning...you have to calculate the cks let me know :)

is this ? right...bravo Angel...

[angelolsp]

Thanks a lot but in this I don't have moddato the break..dvdtuning you can just try it thanks :)

[angelolsp]

The clutch and come next week I write the map with launch and lim at 5500...I just wanted info on geometry how to change the map time an overboost ke then as I understand it, and the duty cycle of the geometry for no to piccare the car...last question 75 mg and the maximum x remain reliable, or we can go over...here are the leon that are really strong and I would not be the less ;)

[angelolsp]

another thing for riguardail limiters of the maf, and was made x 80mg but the map does not need to touch it??or to adapt also to

[angelolsp]

Nn having a gauge fitted and esssendo without diagnosis x vag x now as it may piccare the car?

[angelolsp]

I just finished writing and provarevla machine the launch l I redid and I set to 2700e work the machine the first gears of the pulls well up to 5400 but the lim and the dw are set to 5500 cm ever? Another priblema after the 5000 giruble gears make a lot of effort into entrarr poibadesso feel you have low turbine hiss a bit before with the same prex, the nn was... conclusion the car is fine but am still not happy from the outset that I could not only that, but in 4, but it was after the 180-die a little up to 225 230...and still 0 smoke so you can point to all the 80 or a little more mg? Last question maps injection prov sicurobke are not used because tibripeto the machine smoke does not completely...

[angelolsp]

Then the map injection prov takes into consideration how, in my opinion, this does not smoke, because no injection...now I have solved on iniezzione principal... I would like to touch the 8 maps of the injection times some advice?

[angelolsp]

[angelolsp]

x change the 8 maps duration of the break point are 60.devo get them to 75? saw ke I am injecting 75?

[angelolsp]

I tried again the machine yesterday playing a little with the advances and rifacendola map injection machine, it seems to me that it is not injecting unfortunately I can not do and the log, but the car has 0 smoke in the exhaust and still slow and I think ke has 170 hp or less...what do I limit the gasoluio if the driver wish are at 75 mg, and also the map injection...and then limitiatori pair and the fumes made 80 mg...where is l hitch?? c, and a map of injection o553aa can achieve something she? this is the file that I have developed up to now