ecuvonix for scode m1.5.5,does it work?

[obd75]

good evening, I should make a scodifica total on a 156 1.8 with ecu m1.5.5 hw 947.
should I use ecuvonix,which I generate a file dedicated to the various displacements 1.4-1.8-2.0...
-reading through the rooster v1, which should just do the writing and in the boot with the pin 10 to 12v(I have not yet tried if the avr? communication with the ecu).
-the m1.5.5 use files in BCB while the file ecuvonix are BIN,ECM I exit out of a n?hw 061 that has nothing to do with the 156 petrol if I try to convert with utility the ECM using BCB>BIN does not see the file ,but if use BIN>BCB tells me that the extension does not ? correct.

at this point I doubt there is a,the file generated by ecuvonix ? ready for programming? someone ? ventured to scodificare these ecu using the file ecuvonix?
thanks to those who could? give me some information.

[legendaryslave]

go srivicelo directly inside works great respects, the displacement

[obd75]

thanks 1000

the problems!...
I do try to read the data from the ecu and gallov1 I d? the id...
tried both with 1250 that 1260,I do a test with kwp2000 but nothing.
I read in the info for the m1.5.5 that if the ecu does not ? unlocked code not can you? program,but not d? even the n? identifiers?(kwp "ecu not found")
s? that c'? a point in the part of the card that is used to communicate with the ecu in these cases,I open the ecu and I see that someone has tried this before m?.
they did jump the ecu and I want to make me lose time?
not s? if you go into a diagnosis which is mounted in the car.
for? the doubt that before me,the ecu ? been seen by anyone comes to me,why? they asked me to scodificare this ecu 2-3 weeks f? but they took yesterday.
does anyone know for certain, however, that idendificazione must be done?even though there might be the speech a failure code?the address of the code to program ? true?
thanks again.

[legendaryslave]

L identification must be not allowed? it can be read and can? be written only in boot mode

[obd75]

surely the ecu ? was smanettata by someone before m?.
for boot mode refers to the pin10 12 volt?
I ask why? back time wandering around in the web I found the instructions,where it was indicated a point in the tab hybrid? it was not indicated if it was a communication line or a altraprocedura to write .

[legendaryslave]

No must be placed in the boot opening laecu in the cock 2 there are all the instructions

[obd75]

ok thank you very

[legendaryslave]

ok thank you very
I made this encompasses everything perfect but id do without putting in the boot

[obd75]

I appreciate your effort in helping me...
for? I have not yet met the requirements to view the attachments.
anyway ? exit out of the reality? of the facts.
the colleague who has a workshop and this car, I reported that days back has delivered to the machine with the probblema of the code sporatico and after a few weeks the car ? indented with the carrattrezzi.
also, according to him, the customer is in fact the double game by hacking the ecu by any third party and without mean nothing......
for m? they burned the ecu.
the colleague sure of the controls that had done the previous time has not tried if the entry in the diagnosis,directly removed the ecu and brought it to me

anyway thanks....

[The fact]

hi
you know me-the motivation for which ecm I convert the file from bin to bcb?
tells me so, the selected file has a length that is not valid for the requested operation. thanks to all

[The fact]

another question, legendaryslave has written it so that it works great, but the rooster converts already from the bin to the bcb? thanks riciao

[The fact]

Caz that careless I forgot to say that I made this question because I read on the net that a programmer (I can't remember which) already does this, while others think not because someone urged them to transform the file otherwise it crashes.
thanks riciao :-)

[gadroulll]

as far i know it works .you must load the immo off file, put it on car .get it out from the car and load the original . the off file makes the eeprom virgin and after it work

[The fact]

I made do with a tool official, I understand that you press scodifica to make the total, and if you need to do the partial must be rewritten to the original file after pressing scodifica