Limiter turns on edc16u

[saivivere]

Hello all, has anyone ever eliminated the limitation of a ecu for a golf 5 2.0 tdi 140 cv of 2003? The ecu limits at 4000 rpm. I have said that you have to read the ecu bdm why? the limitation ? in the e2p. I confirm? Thank you all in advance.

[magi1984]

I do not think that the rev limiter is in the eeprom.

[msport (exil77grande)]

the golf v 2.0 tdi 140cv has no limiter at 4000 rpm and pulls over 5000 rpm, mapped,if anything, your problem may be a speed limit that is actually located in the eeprom.

[saivivere]

Then, both the torque limiter, the enrichment and acceleration have been raised, and quite a bit, but nothing the car is limited to 4000. On another golf 2005 a friend with the same ecu, always 140 hp, but with different soft and hard is not happening. It was also modified the speed limiter? but nothing, stops at 4000 rpm, do not really want. Around the net it says that this model ecu has a "vag rev limiter" contained in the e2p and then you can? delete only with bdm. Thanks for the help.

[saivivere]

Anyone ? ever have this problem? Aiutooooo!!!!

[admin]

There is no way to read it in the bdm?
As you have changed the speed limit?

[saivivere]

This weekend I have the chance? to be read in bdm. For the limiter of speed? I changed in the flash read with the serial, as soon as you can place the mod.

[msport (exil77grande)]

This weekend I have the chance? to be read in bdm. For the limiter of speed? I changed in the flash read with the serial, as soon as you can place the mod.

in fact, to begin with, you need to post ori and mod and start a moment to see how it's made to give you some advice.

[saivivere]

Tonight I am attaching the file ori + mod

[saivivere]

http://www.mediafire*****/?4bsvcdbnvqja9lv

here is the link of file ori + mod golf limited to 4000 rpm. Thanks in advance for the help

[saivivere]

Guys, nobody can help me?

[magi1984]

I have searched on the web but apparently the limiter is really in the eeprom, and no one said how to change it, sorry

[msport (exil77grande)]

http://www.mediafire*****/?4bsvcdbnvqja9lv

here is the link of file ori + mod golf limited to 4000 rpm. Thanks in advance for the help


hello,the first thing the next time upload it on the forum and not outside because they need to see just completely average users as required by the regulations otherwise it would not make sense,I looked at the map,then, for me, completely redo the fuel injection,completely redo and in the first break point you escaped the mouse with a peak in the negative,torque limiters I do not like at all,increases in the negative on enrichment and acceleration, and still hurt,even the turbo maps are completely unpacked,I wanted to know, but limited to 4000 rpm in 6th gear at the maximum or up to 4000 rpm with all of the gears?
according to me it depends on the map.

[saivivere]

hello,the first thing the next time upload it on the forum and not outside because they need to see just completely average users as required by the regulations otherwise it would not make sense,I looked at the map,then, for me, completely redo the fuel injection,completely redo and in the first break point you escaped the mouse with a peak in the negative,torque limiters I do not like at all,increases in the negative on enrichment and acceleration, and still hurt,even the turbo maps are completely unpacked,I wanted to know, but limited to 4000 rpm in 6th gear at the maximum or up to 4000 rpm with all gears?
according to me it depends on the map.

Thanks for the response msport. First of all, I apologize for the error with the file upload was not my intention ? only that I had not seen that there was the mode? advanced for it to load. I didn't believe I could do it being still a beginner. For the map, I made it myself so I give you fully reason I do not like it, the problem for? ? any gear enters the limiter at 4000 then ? as it says in magi1984, ? limited in e2p.

[msport (exil77grande)]

Thanks for the response msport. First of all, I apologize for the error with the file upload was not my intention ? only that I had not seen that there was the mode? advanced for it to load. I didn't believe I could do it being still a beginner. For the map, I made it myself so I give you fully reason I do not like it, the problem for? ? any gear enters the limiter at 4000 then ? as it says in magi1984, ? limited in e2p.


the attachment is quiet,for the limitation I repeat that everything is possible, but a lot of 1.9-2.0 tdi edc16 that I did except for a few 140cv that had a speed limit in the e2p and not more than 210kmh I never had or heard of limitations to 4000 rpm even with all of the gears,tell me something with the file gold if you try to sink limits as well to 4000 rpm with all the gears?

[saivivere]

you, the tests were done also with the file ori and limits the same to 4000 rpm, only in first gear, unable to go a little further, but only because? not much load, however, tomorrow morning I have to read the file with the bdm and then send it to a friend for editing, terr? informed.

[saivivere]

So guys, nothing to do, after reading bdm and did change the file e2p to the people who trust the golf fails to go over 4000 rpm and then nothing. Thanks to all for the help.

[frantik3]

limited to 200km/h!!!!!!!

[frantik3]

and I have also seen that to remove a phantom limiter has been used ecusafe

[frantik3]

the map does not express myself even if some of the comment you had

[msport (exil77grande)]

So guys, nothing to do, after reading bdm and did change the file e2p to the people who trust the golf fails to go over 4000 rpm and then nothing. Thanks to all for the help.

can you post the change that you made?

[msport (exil77grande)]

I am attaching the same file but with one change,I think that will not solve the problem, but try not cost you anything,let me know hello.

[saivivere]

limited to 200km/h!!!!!!!

ok frantik3 if it has the limiter at 200km/h, we find on the perch? in the odometer the car is not to be pi? of 210-215km/h


and I have also seen that to remove a phantom limiter has been used ecusafe

that has been removed with ecusafe I wouldn't know since I didn't do it I


the map does not express myself even if some of the comment you had

in fact, not c'? what about the map ? hurt for? there always remains the problem of the limitation of 4000 rpm, also with a map made cos? should still pull a little but nothing.

[saivivere]

can you post the change that you made?

ok poster? tomorrow, the change of e2p at the moment I have it in another pc that I use at work.
Thank you for the file that you posted I can test it on Saturday, why? Franco working out, then just returns the load on the ecu and let you know.

[frantik3]

limited to 210 and them the problem

[msport (exil77grande)]

limited to 210 and them the problem

if you have the solution to download the file ori and e-mail.

[msport (exil77grande)]

however, a restrictor in flash, which I have modified in the test file that I posted was set to 205kmh but then again I knew of the problem of the limitation that is located in the 2eprom especially in the machines of import, but unfortunately I never had the chance to test it,if someone is able we can illuminate.

[frantik3]

address by DE3FC to DE41C

[msport (exil77grande)]

x saivivere do so test my file if not solve try the address frantik3 and let's see if we can solve,let's see if we can get to something,a question, but the air mass meter have you tried to replace it?

[frantik3]

there comes if walls and limited, and all of them the problem raises the limiters and see if eeprom2 there are other 2 and then makes a good map and see that , however, notice a bit of people are not always increasing by 20 or 30% of the car should be going strong there are limits to the design of some of the organs that do not allow it, and then sometimes by up to 5%, I can assure you that the car should be better than 30% personal experience, seeing the car and redoing the car even people of a certain caliber

[saivivere]

x saivivere do so test my file if not solve try the address frantik3 and let's see if we can solve,let's see if we can get to something,a question, but the air mass meter have you tried to replace it?

Then first of all I apologize for not having yet posted the file e2p but the make? soon. With regard to the mass flow sensor air ? was replaced then ? a further test to do, the changed file to the prover? this week-end.

I almost forgot, the golf in question ? import then the problem ? definitely in the e2p. Thanks

[saivivere]

there comes if walls and limited, and all of them the problem raises the limiters and see if eeprom2 there are other 2 and then makes a good map and see that , however, notice a bit of people are not always increasing by 20 or 30% of the car should be going strong there are limits to the design of some of the organs that do not allow it, and then sometimes by up to 5%, I can assure you that the car should be better than 30% personal experience, seeing the car and redoing the car even people of a certain caliber

Ok farntik3 thank you for the explanation, will try? in the address you reported if there are limitations, for the e2p , I seem to have seen limiters.

I am attaching the file of the e2p bed

[saivivere]

So guys nothing to do always the same as the car limited to 4000 rpm not c'? way to make it go further, I have also seen to the address indicated by frantik but I have not figured out how to change it. Thank you again to all for the help.

[frantik3]

in eprom2 not ? limited I've seen and limiters are 300km\h

[frantik3]

755

try this

[saivivere]

ok, thanks frantik sorry if I did not respond immediately but I was out for work, make? the test this weekend.

[mavaila1972]

I agree with motor sport no rev limiter, but the eye to the speed limit