View The Full Version : info on fiesta 1.4 dtci sid802/804
lucatuning
07-05-2013, 17:09
As the title suggests I should make a fiesta ,I Wanted to know if you have to do some procedure different from the other ecu . I read and write the ecu with fgtech and mod the file with ecm 2001 or titanium.
I did a test with a file in my possession of the Fiesta and ecm2001 I recommend scodificare the ori and recode the mod file. Before writing.
What do you advise me???
Thank you for the cooperation :)
use titanium and you don't have problems, trust me, the fact I'm on 2 fiesta and all smooth ;-)
lucatuning
07-05-2013, 17:35
use titanium and you don't have problems, trust me, the fact I'm on 2 fiesta and all smooth ;-)
Ok thanks for the advice :)
I ? come to doubt reading in the forums, why? someone says that every time the phone changes
the code key, and then if I read the file ori , and the fiesta the lead when the mod file .and ready
c'? the risk that the car is not part of pi?.
You know something about it??
You know, I'm inexperienced and I would like to avoid damages to the
especially the perch? I do it on Saturday in time lost, and then not find anyone that can give me a hand in case of problems.
Greetings luke.
never heard anything like that, I a I changed 10 times, and loaded the maps without any problem, if you work at so we pull out something good, there are also a couple of mechanical changes will be simple that you can do, ensure that you get a further increase without compromising the reliability
lucatuning
07-05-2013, 18:10
never heard anything like that, I a I changed 10 times, and loaded the maps without any problem, if you work at so we pull out something good, there are also a couple of mechanical changes will be simple that you can do, ensure that you get a further increase without compromising reliability?
Good to know ;) .
I know that chiudendol'egr with a flange( cap)
you will get some improvement in fluidibilit?
Acceleration less smoke.
Other jobs of mechanics, I don't know :(
what ? a chore to do in the first place, then you can? to work a little bit on the boost pressure and on some changes to the intake to lower even if only slightly the temperature of the incoming air caused by the lack of intercooler
msport (exil77grande)
07-05-2013, 19:56
As the title suggests I should make a fiesta ,I Wanted to know if you have to do some procedure different from the other ecu . I read and write the ecu with fgtech and mod the file with ecm 2001 or titanium.
I did a test with a file in my possession of the Fiesta and ecm2001 I recommend scodificare the ori and recode the mod file. Before writing.
What do you advise me???
Thank you for the cooperation :)
ecm from the tip to which you are referring to you but only if you use the eprom programmer that has nothing to do with the read - write from the serial port.
lucatuning
07-05-2013, 20:10
ecm from the tip to which you are referring to you but only if you use the eprom programmer that has nothing to do with the read - write from the serial port.
ok thanks for the clarification , I wanted to understand propio
:)
https://www.professionalchiptuning.net/showthread.php?3048-parere-su-mappa-fiesta-tdci-sid802&highlight=mappa+fiesta take a look at this and take some inspiration
lucatuning
07-05-2013, 21:32
Thanks Garret x on the link posted and the time spent.I
could only read the comments, why? I am replying from a smartphone
as soon as I can I see the gains from my home computer.
use titanium ? much better than ecm 2001 ;-)
motorsport
08-05-2013, 15:51
I confirm that I do not need to do any special procedure,with mag or cock the reads and writes without any hitch!!
lucatuning
08-05-2013, 16:25
Ok, thanks 1000 :)
As soon as I read the file the place to give me some advice!!!... ;)
Ok, thanks 1000 :)
As soon as I read the file the place to give me some advice!!!... ;)
You can also use the mpps economic and reliable enough on these ecu
lucatuning
09-05-2013, 19:27
You can also use the mpps economic and reliable enough on these ecu
yes I have heard speak well of the mpps, but are in the possession of the rooster v2.
I want to ask you if mpps is the calculation of the cks , on the control units of the Fiesta 06 why? the Cock does not
The should do without problems then depends on the version of the mpps
The should do without problems then depends dalela version of the mpps
and also, of course, the type of the ecu of the car.
lucatuning
09-05-2013, 21:42
and also, of course, the type of the ecu of the car.
Should be a sid 802 or 804
mpps do not read those ecu, already? tried without success
mpps up to version v12 does the simens sid ..
while on the version v16 have implemented
you with both, if you look in the list are not even present, only shows the 1.6 tdci which is fitted with the bosch
yes I have heard speak well of the mpps, but are in the possession of the rooster v2.
I want to ask you if mpps is the calculation of the cks , on the control units of the Fiesta 06 why? the Cock does not
the cks the calculations with ecm tita and ecm 2001
also the kess 1,magpro,flashteck the read and write without problems
but if not ? on the list how do you read it? talk about mpps v12?
There is a version 16?
yes, it exists ,but it is not easy to find it.. or better players is still not there
but if not ? on the list how do you read it? talk about mpps v12?
No it seems pinotec refers to the v16
But the v12 ? upgradeable to v16 so as to read the other ECU?
But the v12 ? upgradeable to v16 so as to read the other ECU?
unfortunately, no
thanks for the info pine
nothing
unfortunately, no
nothing
Ok thanks pino
expect the chinese, as always ;)
expect the chinese, as always ;)
On the web I saw that the damage to just the v16 for? I do not know if you can? trust..
lucatuning
09-05-2013, 22:51
In the list of fgteck v2 there is' no, but calculates the cks. I tried a file sid802
with ecm2001 with the family and the right driver, and the various maps etc. makes Me save the edited file, but seeking the correction of cks in the 2D map can't find it. Mahhh!!!!
In the list of fgteck v2 there is' no, but calculates the cks. I tried a file sid802
with ecm2001 with the family and the right driver, and the various maps etc. makes Me save the edited file, but seeking the correction of cks in the 2D map can't find it. Mahhh!!!!
if you do not make any modification in the file, and normal not change the cks...
if you have changed..check in hex and you will see the differences
In the list of fgteck v2 there is' no, but calculates the cks. I tried a file sid802
with ecm2001 with the family and the right driver, and the various maps etc. makes Me save the edited file, but seeking the correction of cks in the 2D map can't find it. Mahhh!!!!
Have you tried to use titanium?
lucatuning
16-05-2013, 13:32
Have you tried to use titanium?
Maybe I explained it badly, I wanted to say that
when I save the mod file. checksum ? different
from the ori. Then looking At the 2D I can't find the fix that
usually in the Bosch is at the end of the map.
However, I tried also with titanium Idem 2001
in sid the correction of the cecksum ? placed before the various maps, and titanium should calcolartelo automatically when you save the modified file
lucatuning
16-05-2013, 20:46
[QUOTE=garret;43973]in the sid the correction of the cecksum ? placed before the various maps, and titanium should calcolartelo automatically when you save the modified file[/QUOTE
ok the controllero';)
the eyes with the fgtech..I with the v54 mini (clone) 804 the ago without problems, while for 802 need? a byte swap..cos? I said the dealer.
I made a fusion 1.4 tdci without problems.
Powered by vBulletin® Version 4.2.2 Copyright © 2025 vBulletin Solutions, Inc. All rights reserved.