PDA

View The Full Version : immo off 147 1.9 jtd 115hp


sportknight
02-03-2013, 14:27
hi guys,a friend has a problem with his 147,the mechanic has replaced everything but not ? managed to come to****in practice the drive to the 2.5 turns off, or does not rise more?,has also changed the sensor of turns but nothing,has now found a unit to collapse but obviously ? from scodificare

I would like to know,for scodificare these in the serial are not true? you have to unsolder the e2prom and processing it at the counter? and with that program?
egs
02-03-2013, 14:40
But that ecu ?? however, if you have to try only if it goes well you could just make a partial scodifica.....
sportknight
02-03-2013, 14:51
the ecu ? a edc15 the scodifica partial non c'? in time and in carsoftware for this I presume you face only smontanto the eprom,no?
jolidj
02-03-2013, 15:50
the partial only from eeprom . read and put it.
sportknight
02-03-2013, 16:01
Then I need a programmer to read it
legendaryslave
02-03-2013, 16:31
the code is located in the 95p08 if vui make a partial you have to process you, otherwise you can go one-on-new ecu and so to retain all the data, otherwise you need to remove the e2p to do a reading tour of the flasks, and from there the total
sportknight
02-03-2013, 16:50
The 95p08 ? the flash can be read with the serial, that software should I process it?
jolidj
02-03-2013, 16:55
no. wait . the 95p08 and an eeprom in 8-pin , you have to have an eprom programmer to read and write. this if you need to do the partial.
if you need to make the total you have to read the flash into the ecu and from there the scodifica.
they are 2 different memories for 2 different jobs .
I hope that me I know explained.
legendaryslave
02-03-2013, 17:22
no. wait . the 95p08 and an eeprom in 8-pin , you have to have an eprom programmer to read and write. this if you need to do the partial.
if you need to make the total you have to read the flash into the ecu and from there the scodifica.
they are 2 different memories for 2 different jobs .
I hope that me I know explained.
you are correct, maybe I expressed myself badly
freddyecu
02-03-2013, 17:32
Apr? the control units is ori that one of the break picks up the esprom of the code and install it on one of the break... Esprom 8-pin and is close to the flash
msport (exil77grande)
02-03-2013, 17:41
but if this is only a test, why not make a total directly in the serial?
sportknight
02-03-2013, 19:39
and with that program? I've seen that time and carsoftware support scodifica of edc15c alfa romeo.. nyo4?
legendaryslave
02-03-2013, 19:46
the meucci the fa already tested
sportknight
02-03-2013, 20:40
Ok thanks guys
egs
04-03-2013, 11:54
The code is located in part on the 95P08 and in part on the flash.... depends on your chances? if you can do a partial do it on the e2p, otherwise you do the full flash serial....
carbo92
11-09-2013, 22:39
Guys but to make the scodifica total from the serial port, just connect the MPPS or the Rooster v2 to the OBD as if it were a simple writing? Or you have to follow a precise pattern? I have to say that the ecu that I have to scodificare doesn't have his own key so I should scodificarla in serial bypassing before the immo and then write the file scodificato.
Thanks to all
freddyecu
12-09-2013, 01:29
Guys but to make the scodifica total from the serial port, just connect the MPPS or the Rooster v2 to the OBD as if it were a simple writing? Or you have to follow a precise pattern? I have to say that the ecu that I have to scodificare doesn't have his own key so I should scodificarla in serial bypassing before the immo and then write the file scodificato.
Thanks to all

You must do the reading then treat the files read for example with carsoftware and then perform the write.... Keep in mind that carsoftware does not correct the cks .. pay attention you may want to block the ecu....
alex68
12-09-2013, 10:18
x the total by obd is on the flasks, and then calculate the cks ( lights are on the usual engine and code )
legendaryslave
12-09-2013, 14:03
Carbo for the total you need to follow the steps of removing the 95p08, otherwise you can not read it on the bench or dissaldi the 29f400
gcmotor
22-09-2013, 22:00
Sometimes it is not enough to exchange the 95p08, but also the files of the flash.
Another procedure: NB you have to have a device that reads and writes data in the control unit.
procedure to tour:
original unit, which connects the hw to the connector and read the flash.
Take the control unit of the collapse, open it and remove the eprom 95p08 (8pin smd). connect the hw and read the flash, save it and then reprograms the flash read in the original unit. (This step you need to bypass the code for reading from and writing to the control units recovered, but does not work on all units).
now a firm 95p08 of the original unit. clone ok