Bootmode,does it work?

[sportknight]

Hi guys,I have seen that ? a subject not often treated, but very useful
I would like to know,the bootmode you can do with all the programmers serial?
and on that ecu can it be done? you have to have, however the protocol is true?

[sportknight]

nobody knows anything? can?

[FidodidoTuning]

The programmer must have the protocol,so it is a speech that is too generic

[legendaryslave]

it is, in fact, the boot mode you can also make it on 59f

[sportknight]

If the protocol you can? do bdm right?

[sportknight]

I wanted to say you can? make boot

[sportknight]

let me understand one thing,if I have the serial protocol in kline I have to connect the control unit on the kline of the mpps,otherwise canbus
if there is resistance to solder I have to solder

what I do not understand,that it changes from the read in boot mode to that in the serial??
why? if the block the edc15 with the serial boot mode I can resume it?
what has this mode? of cos? powerful?

[explode82]

? a way to put the ecu in mode programming,forcing the apertutra of logic gates without having to go through the request and acceptance of it

[pinotec]

already in a few words, it bypasses the password to access the protocol,so if you lock your ecu immediately after that has been erased the flash,or it corrupts the e2p ,most of the times it fails to resume from the serial,and then it takes the bootmode..or a partial or total on the e2p,this in most cases, edc15 and edc16.

[sportknight]

if the boot mode is not able to set it goes bdm in edc16 and programmer in the edc15 right?

[pinotec]

edc16 to write it after you have fixed via the serial port before you remove the e2p and doing a partial,and after you is to write ,or bdm (nothing bootmode)
edc15 after it is nailed , you can' do bootmode.. or unsolder the flash 29f200/400/800 and write it with a programmer type willem ,or scod partial/total e2p always dissaldandola and riprogrammandola and then writing it to the flash with the serial.

[sportknight]

Ok thanks, saw that I got appointed as the willem, but only connects via parallel port? so it takes an old pc

[pinotec]

willem and now dated, it was as an example.. cmq or pc provided with parallel or usb converter>parallel

[sno74]

I saw the post I wanted to know if anyone has tried to read in boot mode, a sirius 32n of the clio I have seen that with gallo v2 there are instructions attached figure

3021

[pinotec]

on other forums I have read that even in the boot there are able to read the sirius32n in with fgtech2,
only without the boot ...but the file and size is 32kb ..so not useful for the socd total..
I read, though, that someone was able to read with a cable kkl and the sw DDT2000
I'm not sure on this ecu.

[sno74]

in fact, I wanted to do a total on this ecu but the only way ? disconnect the flash now I'm trying to put a socket and then do the tests without desoldering.....

[pitty]

The boot mode ? in practice mode? used to do the backup, if any, with the gallo 2 of the edc17 for example? The Cio? the boot mode ? what a tour, you open the ecu, then weld the pin, gets up and ends up l

[frantik3]

The boot mode ? in practice mode? used to do the backup, if any, with the gallo 2 of the edc17 for example? The Cio? the boot mode ? what a tour, you open the ecu, then weld the pin, it makes a backup and ends with l??

what you say more? precisely, it's called boot mode tricore!!!

[pitty]

ok, but ? correct then all of us? I said? The Cio? the backup of the various control units is always in boot mode tricore? or the situation is different for other units?

P.S.
I believe that we have found here, is it frantik3? eh eh eh!!!

[frantik3]

it is also here

[msport (exil77grande)]

the boot mode tricore applies to the edc17 while for the edc16 is the classic link to the schedule is welded on the pcb or the spring without welding,for edc15 you must desolder the eprom and then read it and write it with an eprom programmer.

[pitty]

mmm interesting... for edc15 for? as I understand until now ? need to do the backup.
For the edc16 agree, or I dare via obd to do both reading and writing? Leaving aside the speech ? always convenient to do so.
In practice what I ask ?: you as you work? Always back-up of each unit or only some?