View The Full Version : eprom programmer,what to do
sportknight
17-02-2013, 03:06
so guys,first of all, I would like to figure out what to do with an eprom programmer
I can, for example, place the edc15 in the case of the block?
can I remap the ecu pi? old type motronic etc?
which programmer should I take?
I saw that there are x-progr,willem,wellon,top3000,upa, etc.
which would you recommend for me to spend not so much?
cinqueturbo
17-02-2013, 14:57
I recommended year:
LAB TOOL 48XP
FOR THE PROGRAMMER EEPROM SPEND MORE BUT GET THE TOP AND IS REALLY SMART BECAUSE IT TELLS YOU WHICH PIN MAY NOT BE MAKING GOOD CONTACT
these are the exact words..
can read and write a lot of Eprom and chip, see the features...
sportknight
17-02-2013, 15:18
Where can I find it?
cinqueturbo
17-02-2013, 15:29
Hello! you or just answer...
sportknight
18-02-2013, 08:49
the labtop can not find it,I saw the x-prog
can do to the case? do I need more? to be on the safe side with the edc15
sportknight
19-02-2013, 17:07
no one can give me an advice?
I need a programmer that does not cost much and that will allow me to restore the edc15 and maybe some interface that you sputtan... :D
the edc15 bring you to the place in boot mode...
I have never had need? of dissaldarle...
anyway, okay any programmer that face those eprom with its adaptor...
see you around what you find according to your budget and buy it.
sportknight
19-02-2013, 17:17
a,ok,thanks, good to know
that eprom has to do anyway to be good? which eprom are needed in this field? cos? to me straight edge ;)
sportknight
19-02-2013, 23:07
I saw willem but I noticed that the power supply ? usb but the data are parallel then I don't know how to connect it to my current laptop..
confirmed?
legendaryslave
19-02-2013, 23:10
I saw willem but I noticed that the power supply ? usb but the data are parallel then I don't know how to connect it to my current laptop..
confirmed?
are you council or the upa very valid use for many years also the xprog goes very well ? for some years I have taken the gx4 and I have to say that he is fine I do not recommend the willem ache if ? was my first programmer
sportknight
19-02-2013, 23:26
but the xprog does not have the adapter for eprom zif 40-pin?
sportknight
22-02-2013, 11:32
ragazziiiiiiii,then? qualce programmer should I take?
the willem no, why? does not communicate with the usb port, but only through the parallel port
the xprog ? the one that has more? adapters and costs very little, but I have not seen the adapter zif 40-pin
then I saw the cinesone that costs very little,no one has it? ? the lag g540 with 2 or adapters plcc32 and plcc40
need those adapters? or are more? useful those who give with xprog?
according to the eprom, eeprom, micro, etc... that you have to eventually make purchases...
who do you serve 2 of programmers who each other are offset...
sportknight
22-02-2013, 16:25
ok thanks :)
progress
22-02-2013, 19:45
I have the upa that usually use for the drivers and I am fine for the engine control units never even used because I just started with the tuning of the ecu, however I advise you to see the car park you have then if you have money to throw away like others said buy 2 so you compensate
I also use I have g4 upa and xprog but go quiet g4 works well and has a price that is not an exaggeration.....
sportknight
02-03-2013, 15:11
between the upa and the x-prog to begin what would you recommend for me?
maku1977
03-03-2013, 00:44
I use a GQ-4X ... simple with fequenti updates..... and never misses a shot!
sportknight
03-03-2013, 08:04
Azz, I'm confusing the issue even more ideas
Sportknight I have the upa and tl886cs with almond eyes and the last quest I got it with all the adapters that were also normal that costs more? so if I have a problem with some EDC15 out the flash and do the same cmq cmq not enough the same, it would take the xprog to cover a p? pi? the motorola.
According to me you need at least 2 programmers, the cio? I speak of the clone, where the price ? enough content x who does not every day, senn? of programmers as good as you ? gi? was advised there are but the normal prices are more? high.
Xtreme0303
18-03-2013, 22:14
on a site I found the diagram for diy the xprog, no one has tried it?
I advise you to buy a clone...
Xtreme0303
18-03-2013, 23:46
mmm...a name to do a search? thank you
please contact admin via the on-line shop you can? help and if you have issues then tells you to use.....
Xtreme0303
19-03-2013, 00:30
ok thank you!!
sportknight
22-03-2013, 09:10
to work on 29f that the programmer need? I saw that both the upa that the xprog that I was very interested don't do them..
to work on 29f that the programmer need? I saw that both the upa that the xprog that I was very interested don't do them..
Hello! I took the TL886SC ago, many chip including 29f only that the adapter SOP44 did not give it almost never with the programmer and to the limit take it apart, I should get the sti days, already? tried it on AM29F800BB 48pin and that's okay.
between the upa and the x-prog to begin what would you recommend for me?
xprog is a good thing.
virus1976
28-08-2013, 04:46
I appended I too am hoping to give a useful contribution to the discussion by bringing a bit of the tests made both on the job and with friends on some of the programmers that are on the market
top3000/3100
On paper they seem to have good potential? (40.000 unit? supported), but in practice are of disasters.
The software ? partially in chinese (the lesser evil),several of the unit? listed are not supported, the manuals ? totally absent, the Test IC is not working.
In any case, I've had problems with the ZIF.
Genius g540
? was one of the first programmers usb that I had and can I say that ? very reliable, unfortunately, not ? pi? developed and has a park unit? very limited.
GQ-4X
the laboratory use and does what it says ? always well-supported and for what it costs it is worth to buy it
wellon vp190,vp280,vp380,vp480
you can easily find around are reliable and support between 14,000 and 32,000 out unit? but they are now models out of production, especially the first 2.
wellon vp290,vp390,vp590, vp596
have replaced some older models do not have excessive costs and to cover abbondantememte the normal requirements
Wellon gp-1(gp-10)
it is part of the high-end programmers, the gp-1(version for european markets) is to be found for affordable prices, has support of about 32,000 units.
Regarding the Wellon around there are several models with acronyms strange type vp498,vp908 etc are clearly of the buffaloes, they are often older models with the casing changed
Xeltek superpro 500P
I have the version with almond-shaped eyes, never a problem, even if there are some things (like the usb connector and power connector) welded to the good(that you can't? have everything).
Supports nearly 43,000 units? and a documentation of all respect, there is, for some time the version 600P pi? fast and with some unit? added but I don't think the cost justifies the purchase.
Conitec GALEP 5
The use in the laboratory for about 2 years and ? infallible coast of pi? of the other but ? the one that has by far the best support hw/sw.
also available are (always produced by conitec) a series of brackets and adapters for the reading of the majority of the eprom/flash etc.
to work on 29f that the programmer need? I saw that both the upa that the xprog that I was very interested don't do them..
I use a g4, I have never failed me there wants to adapter and a little patience are difficult to position on the adapter, you must check the pins are not bent......
I use a g4, I have never failed me there wants to adapter and a little patience are difficult to position on the adapter, you must check the pins are not bent......
you can confirm the same, even if I suggest that in our field we would like to all.
to begin with the g4 goes well then when one wants to continue you know the things to buy are never-ending depending on the work you do....
glittering chiffon party dress.fitted
28-08-2013, 08:51
From my experience I advise you to first of a upa, then another recommended by colleagues, for gq to ****s e2p I was a little disappointed not to act in 16-bit 93lc66 ciai and good work.
I work with gq4x and upa, and I am fine..the 29f200 or 400 do that with the gq4x with its adapter and never have problems
glittering chiffon party dress.fitted
01-09-2013, 19:09
I think I've only said that the gq4x does not read the e2p in 16-bit I also use adt to read the 29f200 and 400 hello.
sportknight
01-09-2013, 19:40
to work on a 75 with a 27c256 I saw that the tl866cs ago but which adapter should I get?
Sorry that I may have missed some of the post but the GQ-4X the 29f800 the ago with no problems ?
.. if it's so? it will be? my next purchase !
legendaryslave
01-09-2013, 23:02
Without problems
Without problems
Thanks , I took a chinese complete with adapter but not me, the reading seemed good but the writing was a mess, you know, even if he has a guide on how to proceed with the read/write memories ?
I do not happen to use it all day for? I ? served pi? a time, and expense ? fairly contained.
sorry guys,I finally got a wellon vp390 and sincerely, using it to 27c of the 75 I had not had problems.
A few days ago I had read a 29f400bb a sid 305,I am going to read, and no,I do not read the contact of the first pin of the flash.
I want to put the memory on the ecu believing that there has been no consequences, and instead, the ecu blocked.
fortunately rewrite the file in serial, and the car starts again.
yesterday, however, 29f400bc,same problem
the flash is 44-pin on two sides with adapter 44sopzif
I checked all the welds and they are ok both on the programmer and the adapter
Take a galep 5 golds and go quiet
Powered by vBulletin® Version 4.2.2 Copyright © 2025 vBulletin Solutions, Inc. All rights reserved.