PDA

View The Full Version : Help map opel corsa


ecutano
16-02-2013, 21:23
Raga hello , I need some advice for this map , they are not pleased with the performance , the machine is good for? I was expecting a higher increase , what do you think ??

Z13DTH
W0L0SDL.............
MAREL0100.
HW03A3137S15
3137S151..
explode82
16-02-2013, 23:34
then we have a shortage of torque limiters,injection times are made very badly as I see it, and start from the beginning and too much at low load,doesn't it ? been done the rail and with the pedal you can? do much much better
ecutano
17-02-2013, 00:44
then we have a shortage of torque limiters,injection times are made very badly as I see it, and start from the beginning and too much at low load,doesn't it ? been done the rail and with the pedal you can? do much much better

Hello explode82 , do you mind if I indicate the beginning of the missing map ? Thanks
explode82
17-02-2013, 01:42
see according to me if you want to learn you have to try and do it alone,however you can route as by the spirit of the forum,a torque limiter that is not the fact is, after closing the egr ,and ? very similar to the 2 that are one behind the other,then returns the original time and rifalli how do you think the righteous do? leave the first 6 curves ori, then redo the better the pedal.............
ecutano
17-02-2013, 11:07
see according to me if you want to learn you have to try and do it alone,however you can route as by the spirit of the forum,a torque limiter that is not the fact is, after closing the egr ,and ? very similar to the 2 that are one behind the other,then returns the original time and rifalli how do you think the righteous do? leave the first 6 curves ori, then redo the better the pedal.............

I've made some changes , see what you think?
explode82
17-02-2013, 23:59
for the rail you started too soon parts a couple of corners later,and toglici a couple of points where you gave 10 and 11,the turbo ? ok, and also the limiters even if one is still 1, but you need to adjust the injection timing
ecutano
18-02-2013, 00:44
for the rail you started too soon parts a couple of corners later,and toglici a couple of points where you gave 10 and 11,the turbo ? ok, and also the limiters even if one is still 1, but you need to adjust the injection timing

Which would be the final limiter , I do not see him ! postresti give a little help in the pi? ?
explode82
18-02-2013, 01:49
it is, after closing the egr
ecutano
18-02-2013, 13:13
it is, after closing the egr

And this ??
explode82
19-02-2013, 01:40
no one ? the management of the egr is still after and ? only one ? equal to 2 consecutive neighbors
magi1984
19-02-2013, 08:26
sorry but don't you first tell him the address?
explode82
19-02-2013, 21:22
the magi figured if I have the problem in giving him the address,indeed,but being that you want to learn,not c'? the best way to practice in the identification in 2d maps,if I didn't want to help me I was in silence............of course I'm driving step-by-step
ecutano
20-02-2013, 00:09
the magi figured if I have the problem in giving him the address,indeed,but being that you want to learn,not c'? the best way to practice in the identification in 2d maps,if I didn't want to help me I was in silence............of course I'm driving step-by-step

And this ???
If ? you , we hope !, what is the function ??
explode82
20-02-2013, 14:08
is the address ? from 0848AA to 0848B6

yet ? equal spiaccicato on those 2 consecutive XD

compare them and then tell me
ecutano
21-02-2013, 07:31
is the address ? from 0848AA to 0848B6

yet ? equal spiaccicato on those 2 consecutive XD

compare them and then tell me

Thanks for the info , or seen through the addresses of the limiter , even if I can't see the two consecutive , however what is the use of this limiter ??