removal of the limiter speed smart

[freddyecu]

hi tweety I should remove the speed limiter? on a smart... by opening the files with ecm titanium map speed limit and set 135km/h ... do you know how to remove it or take it to the highest? I attach the files so you can control it better... thank you in advance

[magi1984]

to use it with ECM just edit the value manually. this was what you wanted to know?why? I am afraid I did not understand the question

[freddyecu]

If you run the command add 5 should not be... but If the edit command lets you change the value ? I thank you in advance

[magi1984]

http://s13.postimage.org/5jgdlyer7/Immagine.png

enter in the map limiter of speed.
you have 6 similar maps.
press the enter key to select the map 1 of 6
edit the value with the button you see above in the picture

[freddyecu]

Ok thanks as soon as I go home I try...? if they come? in the speed limiter? then where it says add 5 1 or subtract 1 5 I edit and write the new value and writes it then I save the changes.. If for? the open back 135 km/h

[freddyecu]

Or moved the limiter to 299 all ok thanks again

[James]

foi do I know if you can fill it!:)

[sportknight]

hahahaha how much does a smart without limitation with respect to a limiter?

[msport (exil77grande)]

if the mapped decently even 170kmh

[freddyecu]

Between today and tomorrow I write and I make? know the speed? maximum...

[leandro89]

news? on speed? maximum?

[explode82]

brave who wants to get with that little box 170 ahahahhahah

[alex68]

gi? also of interest to me to know this.

[msport (exil77grande)]

news? on speed? maximum?

I know that for the high speed if they' forgot to update the post.

[freddyecu]

Tested, but continues to stop at 140

[frantik3]

Tested, but continues to stop at 140

if you do not push a lot to the map, not the salt of very

[leandro89]

today a friend of mine has turned off the speed limiter? by connecting pin 5 to pin 7 of the obd! the fact that you also turn off esp

[explode82]

well, it works for sure so,but already lost not ? keep well the road to the smart species at a certain speed?,then you turn off esp, I would say that this car becomes suicidal in my personal opinion

[max75]

let me know when ? in circulation.......I think of the 170km....but be a little scared....quidarla...

[gfr]

but how do you see the speed? my the bottom of the scale, and the ha160 and he overtook him in a big way! but I don't know the max speed

[Xtreme0303]

sorry for the ot, but you use the same method for over-the bmw and mercedes?

[djbiugi]

Hello extreme..oh god,if we talk about edc16, bmw has in the area of torque limiters, mercedes shortly after the management turbo..

Returning to the discussion of the limiter, Smart, 800cc, model 450 the thing ? simple (in 2D the decimal value ? 13500, which is the equivalent of 135 km/h) , but on the 451 54cv that mounts edc16? I have tried to manage it as by setting Titanium (wrong) and also as a classic edc16c32 mercedes, but to no avail unfortunately :-(

[djbiugi]

I forgot...on the 451 stops at 150km/h on the speedometer..even if the house says 145km/h...I have not found any decimal value to 14500 or 15000 slut zozza :-(

[goku]

Hello..what kind of Smart? ? and what was read.. I Wanted to do the same thing on a 1000 but I'm not eiuscito to read it with the gallo2 ne mpps...

[djbiugi]

The model 451 ? a ForTwo...model 2011-2012 x understand...read it in the Can like a normal Mercedes edc16c32 with gallo official

[explode82]

the gasoline does not,or at least there are no protocols

[gfr]

the petrol 451 : welding 2 resistors and pinout , 100% sure I've done a little bit, and assemble a me7.7

[djbiugi]

2 resistors where? In the comb unit?

[goku]

the petrol 451 : welding 2 resistors and pinout , 100% sure I've done a little bit, and assemble a me7.7


2 resistors where? In the comb unit?
..? then? Resistance where? By how much? ? with what I read/write, and type of selection?

[Ghizmo]

the petrol 451 : welding 2 resistors and pinout , 100% sure I've done a little bit, and assemble a me7.7

Good to know, can you give some detail in the pi??

[magi1984]

should be in the boot with the cock

[frantik3]

it is in the boot with the cock made many

[explode82]

but not ? a bosch 7.70? in the documents, not the door strange thing

[dayano1]

someone can? post the photo to link it with the wing nut in the boot of the smart bosh 7.7.0, I follow the photo of 7.70 but I did not connect me to the perennially error the cock
thanks in advance

[admin]

The 1000 benz is only done in the boot by welding the two resistors
The schema you from the kess when you select help, if someone
has the pu? post

[carmageddon]

I remember having to do the same ecu in the boot, and read and write without problems, but with the wrong checksum, correct it before with a manager and not doing it correct to fgtech

[dayano1]

ok to check, but maybe he could get there ;)
as written before, I doubt that there is something wrong with the photo link galletto v2 xch? not "connect" continues perpetually to give me the error

[carmageddon]

those that have followed you are nothing more than patterns of alientech, I believe that they are accurate as the one that did the ecu in question follow? the schema of fgtech...in another schema, always alientech, on the negative ? to a pin that is different as you can see.

http://img14.imageshack.us/img14/9831/sh7c.png (http://imageshack.us/photo/my-images/14/sh7c.png/)

Uploaded with ImageShack.us http://imageshack.us)

[dayano1]

ok great thanks today in the afternoon I try. now, I have not with me the photos but my ? different, makes me connect many more? pin

[carmageddon]

excluding the scheme fgtech/alientech where you solder the two resistors and connect the same pin but with the negative to the pin 59 instead of 58...the other schema ? this, there are no others that I know of.

http://img189.imageshack.us/img189/2448/qu3t.jpg (http://imageshack.us/photo/my-images/189/qu3t.jpg/)

Uploaded with ImageShack.us http://imageshack.us)

[carmageddon]

as you can see, it only adds a positive to the pin 65, but on the negative ? always to the pin 59 and not 58