X14XE
27-01-2013, 20:46
Hello everyone and congratulations for the forum,
Moving on to the "core" of the problem ,
I inquire
in the OPEL ASTRA 1.4 16 v ( astra f 1997 ) with X14XE engine , sporadically turns on me the light of the diagnosis, I decided to buy a interface bluetoot POWER2 based on the ELM327 will be connected ( via bluetoot ) to the tablet ( S. OR ANDROID ) using the software TORQUE PRO rel. 1.6.30. :
http://torque-bhp*****/
http://imageshack.us/photo/my-images/84/power2obdelm327.jpg/]
http://imageshack.us/a/img84/6421/power2obdelm327.th.jpg
At the moment I have some problems of "communication" therefore, I ask You, "first" if I confirm if the "grip" diagnostics of my car ? OBD2 ( l' interface ? nested perfectly in the socket ... so I presume yes ) ; then, eventually, if someone has already? had experiences in relation with the above-mentioned hardware/software mentioned above and, in particular, on the engines of the OPEL.
For the hardware, I used this ...accurate...accurate :
Product description
* Andriod / Droid / Torque compatible with ELM.
* Bluetooth connection, No need Batteries, cables, or switches.
* Displays the data of the engine in direct on your Android phone.
* Retrieve fault codes (DTCS) and clear lights check engine.
* Retrieve fault codes (DTCS) and clear lights check engine.
features:
* Read diagnostic trouble codes, both generic and manufacturer-specific, and display their meaning (pi? 3000 generic code definitions in the database).
*Erase DTC and turn off the MIL (light "Check Engine")
* The display of the data of the current sensor, including:
* Engine RPM Load
* Calculated value
* Coolant temperature
* State of the fuel system
* Speed? of the vehicle
* Short Term Fuel Trim
* Long Term Fuel Trim
* Intake manifold pressure
* Timing Advance
* Temperature of the intake air
* Air Flow Rate
* The absolute position of the butterfly valve
* Oxygen tension sensor / associated short term fuel trims
* State of the fuel system
* Fuel pressure
* Many other
Manual in English only, pls observe before you buy
Pair Bluetooth code ? "1234" or "0000,, but someone also says "6789" ( the latter I have not tried it ).
The underlying "evidence" specific that have been made with the "PICTURE" of the car in position ON, and then also with the car in motion.
The same "interface" referred to above, as soon as connected to the socket under the steering wheel ( fuse box ) reports with one of the led ( red): the "operation" once "hooked" by the Bluetooth of the tablet you can see a scan in the return of the LEDS on the interface ( ELM327 ) and then to "stabilize" on only RED led is on, at this point in the tablet in addition to the icon of the GPS, of the tablet and the interface will light up the icon on the car for? continues to FLASH.
Checking for? in men? ADAPTER STATUS I see that the item :
- Bluetooth-enabled = YES
- Connection to the ECU = YES
- Connection to the ECU = NO
and ? right here that I am afraid that is the problem !!!
A "minimum" of communication I assume that there is as yesterday " by trying another program I would not have returned ZERO error code and the battery voltage ( 14.4 v - 14,3 ) variable why? the car was in motion.
The program "official" however, it should be this TORQUE PRO , the interface seems to work and communicate with the tablet but NOT with the "unit" as in addition to those two data above is not returned me to the other.
What I "rhoda" ? that I don't know if there is a "problem" in the interface, POWER2 ELM327 ( therefore at the moment I'd still be in time for me to replace it from AMAZON ) or if it is just a matter of my inability?..*****and I assume, not activating it well via software.
I look forward to and count on your expertise , maybe if one "knows" the program in two seconds "understands" where is the problem why? maybe I have not activated this or that voice or not, I've entered a particular parameter is required.
Moving on to the "core" of the problem ,
I inquire
in the OPEL ASTRA 1.4 16 v ( astra f 1997 ) with X14XE engine , sporadically turns on me the light of the diagnosis, I decided to buy a interface bluetoot POWER2 based on the ELM327 will be connected ( via bluetoot ) to the tablet ( S. OR ANDROID ) using the software TORQUE PRO rel. 1.6.30. :
http://torque-bhp*****/
http://imageshack.us/photo/my-images/84/power2obdelm327.jpg/]
http://imageshack.us/a/img84/6421/power2obdelm327.th.jpg
At the moment I have some problems of "communication" therefore, I ask You, "first" if I confirm if the "grip" diagnostics of my car ? OBD2 ( l' interface ? nested perfectly in the socket ... so I presume yes ) ; then, eventually, if someone has already? had experiences in relation with the above-mentioned hardware/software mentioned above and, in particular, on the engines of the OPEL.
For the hardware, I used this ...accurate...accurate :
Product description
* Andriod / Droid / Torque compatible with ELM.
* Bluetooth connection, No need Batteries, cables, or switches.
* Displays the data of the engine in direct on your Android phone.
* Retrieve fault codes (DTCS) and clear lights check engine.
* Retrieve fault codes (DTCS) and clear lights check engine.
features:
* Read diagnostic trouble codes, both generic and manufacturer-specific, and display their meaning (pi? 3000 generic code definitions in the database).
*Erase DTC and turn off the MIL (light "Check Engine")
* The display of the data of the current sensor, including:
* Engine RPM Load
* Calculated value
* Coolant temperature
* State of the fuel system
* Speed? of the vehicle
* Short Term Fuel Trim
* Long Term Fuel Trim
* Intake manifold pressure
* Timing Advance
* Temperature of the intake air
* Air Flow Rate
* The absolute position of the butterfly valve
* Oxygen tension sensor / associated short term fuel trims
* State of the fuel system
* Fuel pressure
* Many other
Manual in English only, pls observe before you buy
Pair Bluetooth code ? "1234" or "0000,, but someone also says "6789" ( the latter I have not tried it ).
The underlying "evidence" specific that have been made with the "PICTURE" of the car in position ON, and then also with the car in motion.
The same "interface" referred to above, as soon as connected to the socket under the steering wheel ( fuse box ) reports with one of the led ( red): the "operation" once "hooked" by the Bluetooth of the tablet you can see a scan in the return of the LEDS on the interface ( ELM327 ) and then to "stabilize" on only RED led is on, at this point in the tablet in addition to the icon of the GPS, of the tablet and the interface will light up the icon on the car for? continues to FLASH.
Checking for? in men? ADAPTER STATUS I see that the item :
- Bluetooth-enabled = YES
- Connection to the ECU = YES
- Connection to the ECU = NO
and ? right here that I am afraid that is the problem !!!
A "minimum" of communication I assume that there is as yesterday " by trying another program I would not have returned ZERO error code and the battery voltage ( 14.4 v - 14,3 ) variable why? the car was in motion.
The program "official" however, it should be this TORQUE PRO , the interface seems to work and communicate with the tablet but NOT with the "unit" as in addition to those two data above is not returned me to the other.
What I "rhoda" ? that I don't know if there is a "problem" in the interface, POWER2 ELM327 ( therefore at the moment I'd still be in time for me to replace it from AMAZON ) or if it is just a matter of my inability?..*****and I assume, not activating it well via software.
I look forward to and count on your expertise , maybe if one "knows" the program in two seconds "understands" where is the problem why? maybe I have not activated this or that voice or not, I've entered a particular parameter is required.