View The Full Version : Programmer Upa
Hello guys.. those of you who often use this programmer ??
I need help.. I have 2 but none work for me.. ( 1 original and a clone )
I look forward to the info..
thanks
azz... nobody uses this programmer?
carlo abarth
26-01-2013, 01:22
look, if ec l you have the original a friend of mine had stopped working contatando erlasoft they sent a little program that you restored , did you contacted???
Hello
Upa original elrasoft, works 100%, used many times in the years 2006 onwards.
you can be + clear , what you need to know what are the errors of your upa
motorsport
25-03-2013, 00:45
also I use it works,what are the tests that you did?cables,power supply,db,are affixed??
Hello Audi sp,
that problem right do you have with the programmer?
I also use a UPA, without problems.
the simple test that I have done recently ? to read an eprom 93c66 or 24c04.. not c? was to read it tomorrow.. if I can do a screen and I'll post it..
even I have all the kit in the original schedule, but nothing..
I use without problems... when you open the program that the upa is recognized the hw? in the above program, in the item "tools"c'? a function "hardware test"if I'm not mistaken, launching this function, you should do a sort is diagnosis in the programmer to locate internal faults(segiu the instructions during the test).
one last thing, once I was freaking out suddenly did not want to work... in the end the probblema was the usb cable(even though it works),you must use propiro the one provided.
glittering chiffon party dress.fitted
30-04-2013, 09:10
I also use the upa clone never had any problems, I obd75 check that you have listed hello.
guys ,did you know that the.upa can also be used as an oscilloscope?
msport (exil77grande)
19-05-2013, 10:46
guys ,did you know that the.upa can also be used as an oscilloscope?
I know that when you are new in a forum before you read the rules and then we are presented with in the appropriate section.
Guys I was thinking of buying a programmer upa usb version 1.2.. what do you think?
glittering chiffon party dress.fitted
15-09-2013, 20:48
Good buy hello
While the Model XPROG-M V5.0 ? The better the UPA?
cinqueturbo
22-09-2013, 11:44
the simple test that I have done recently ? to read an eprom 93c66 or 24c04.. not c? was to read it tomorrow.. if I can do a screen and I'll post it..
even I have all the kit in the original schedule, but nothing..
to resolved in the end?
carlo abarth
22-09-2013, 14:41
I use it often and I find it very good I also xprog but and a slaughterhouse...the council on upa!!
Guys I was thinking of buying a programmer upa usb version 1.2.. what do you think?
faberecu
23-09-2013, 16:32
but with xprog certain micro them read with Upa read them but they break....
the problems of reading with the upa data 100% from the socket if not ? weld-on or if it has ever worked ? damaged
I have read and written about everything , just to add the Piasini are not able to read properly write the 25p32v6g if I remember well , but did not ? in the list
I have had a few of the scripts for the upa , they are really cute, by reading directly the pin code
script upa examples
cinqueturbo
23-09-2013, 22:44
but with xprog certain micro them read with Upa read them but they break....
the problems of reading with the upa data 100% from the socket if not ? weld-on or if it has ever worked ? damaged
I have read and written about everything , just to add the Piasini are not able to read properly write the 25p32v6g if I remember well , but did not ? in the list
I have had a few of the scripts for the upa , they are really cute, by reading directly the pin code
script upa examples
Sorry but what are these scripts ?
how to use?
faberecu
23-09-2013, 23:00
decompatta and put them on the scripts folder dell upa and toggle the tools menu, it seems to me
once you have read the memory utilizzaondo the script that appears in the middle of the various types of chips you get the pin code
clearly each script works for families
? cute
cinqueturbo
23-09-2013, 23:05
decompatta and put them on the scripts folder dell upa and toggle the tools menu, it seems to me
once you have read the memory utilizzaondo the script that appears in the middle of the various types of chips you get the pin code
clearly each script works for families
? cute
but there are different kinds of scripts?
Thanks for the info, are the first steps with the UPApa:p
script,pin code?
sorry, we speak of the pin code by reading the micro inside elle immobox?
or you mean the security byte of some motorola?
faberecu
24-09-2013, 13:14
no, they are scripts that are created by third parties for the immediate reading of pin code is a body or bsi or ecu
reading the memory or the micro
there are several scripts for different brands , or immobox are also full of photos
speed up the work
nothing earth-shattering, but comfortable
a sort of improvement ...
linus146
04-10-2013, 20:38
I introduce myself on the discussion because it can be useful to colleagues and I confirm that to me as well, and happened to have problems on the programmer, upa official and have been followed in an exemplary way by the upa ( elrasoft) that have guided me to resolve the problem.
even if I prefer xprog
cinqueturbo
04-10-2013, 21:02
but where can you find these scripts?
you give me a tip?
I'd be really interested...
I was thinking of tiling a UPA to my GQ-4X
a strange curiosity?: I just bought a caliper ?m to read the SOIC8 without desoldering, but now I have doubts on the actual reliability? this programming system.
It is reliable?
It is more reliable with a UPA compared with the GQ?
thanks
linus146
05-10-2013, 15:09
for reading, you always have to unsolder
otherwise, how do you correct a reading done wrong?
in fact, it was my doubt!
but since I see that these calipers little ones around, I have the imnpressione that many use them without even unsolder....
linus146
05-10-2013, 19:43
it always depends on what you need to do,
second, what do you do if a reading is made badly, you notice it immediately
according to what you do instead, you notice it after that maybe the machine nn more
they are certainly comfortable, but you must always be ready and equipped to unsolder
but there are different kinds of scripts?
Thanks for the info, are the first steps with the UPApa:p
Hello
Yes, they are different, some for inmo, the other for the pin, the other for miles, etc.
for reading, you always have to unsolder
otherwise, how do you correct a reading done wrong?
Hello
No, no you have to unsolder, some eeprom you can llere with the caliper, and the other not.
You will only need to asicurartti here the reading is good.
Here, then, such as the eeprom are read with the caliper?
I simply try to read most times and see if the check ? and always the same. But this does not protect you from being able to corrupt the data, but...
cinqueturbo
06-10-2013, 12:58
Hello
Yes, they are different, some for inmo, the other for the pin, the other for miles, etc.
gezame, but where to find them?
ecutuningpro
06-10-2013, 14:02
you better get to unsolder always, read with the caliper of the chip soldered on the board many times ? busted.
linus146
06-10-2013, 22:40
I see so
at least at the beginning you make of the readings is with the caliper that can be seen
then when you're reading done well by a hurt, you can also read directly only with the caliper
p.s. to me pocp time ago and asked for a reading that seemed to be well made, but it has left a string, all ff ff ff ff ff
and was that where there was code key
ecutuningpro
07-10-2013, 11:53
on purpose to avoid problems of the kind I prefer to unsolder always.
linus146
09-10-2013, 03:26
in fact,................
trust is equal to rub--------
michele30
12-10-2013, 17:26
c'? a guide (or manual ) of this upa on how to connect the calipers to read or even to unsolder and which player esare ?
linus146
12-10-2013, 23:36
you how to install the program there is the guide
michele30
13-10-2013, 13:27
can you tell me how you connect the memory MC68HC05E6 of the micro framework y to the upa?
I have read around that you just have to unsolder some pins to connect it but I don't understand how do I do the link
any advice?
cinqueturbo
16-10-2013, 00:54
Hello
Yes, they are different, some for inmo, the other for the pin, the other for miles, etc.
Sti script are worse than the damos...
did not find a lot of info..
I'm TomSad that developed pei script but I do not find it in the internet.. at least I can't do it...
http://www.youtube*****/watch?v=CVOdYNMe0T4
someone knows it?
or can you? help me?
michele30
26-10-2013, 12:27
I have a problem with the upa, gives me an error while I run the hardware test, ? normal?
I enclose a photo
cinqueturbo
26-10-2013, 14:38
I have a problem with the upa, gives me an error while I run the hardware test, ? normal?
I enclose a photo
But you connect it to USB or to a multi USB hub?
s? so connect it to a USB port on the pc..
Then or since to the home editions is not suitable with these interfaces in general...
michele30
26-10-2013, 17:06
I use this for all the programs and I have not had my problems.
in most there are specific drivers for w7 32 bit or 64bit.
I don't think it's a problem of windows
cinqueturbo
26-10-2013, 21:07
I use this for all the programs and I have not had my problems.
in most there are specific drivers for w7 32 bit or 64bit.
I don't think it's a problem of windows
To solved it?
the operating system was not saying that he would not go,
but it is certain that the professional or ultimate year a step in the pi? to work on them.
faberecu
27-10-2013, 08:28
I have a friend who has a lot of scripts like the ones I posted I do send. We can ask the admin if we open a section dedicated to it. And I put all the ones that I find. We can do a data bank.(
cinqueturbo
27-10-2013, 09:54
I have a friend who has a lot of scripts like the ones I posted I do send. We can ask the admin if we open a section dedicated to it. And I put all the ones that I find. We can do a data bank.(
That would be awesome..
no need to open a section, just open a new topic (Script) in the section programmers..
faberecu
27-10-2013, 10:41
Ok I'm going to do...
cinqueturbo
27-10-2013, 10:58
Ok I'm going to do...
Thanks I am very interested and anxious..:p
cinqueturbo
28-10-2013, 14:08
Ok I'm going to do...
faberecu news??
to change your mind?
faberecu
29-10-2013, 20:02
no, they are only inkasinato finished now du bins y 1.3 mjet and bmw 320 d 163.hp incasinate by a professor at the university of kasini
I have made the request to my friend , just mail me place a collection cute
net_proo
07-02-2014, 11:54
hi,
anyone have the upa scripts for immo, i see in other pages to many but can't find ...
leandro89
07-02-2014, 17:37
hi,
anyone have the upa scripts for immo, i see in other pages to many but can't find ...
using a translator to write
net_proo
07-02-2014, 22:44
hello,
I'm sorry for the error, I forgot to traduct the text
Someone has the script UPA for immo, I see the other pages of many, but can't find it ...
Guys I would like to buy it also I to clone the immo e2p.
What is and what is not?
The merits and defects of the calipers apart?
I have suggested that to spend 100 for the clone, better 300 the official update to life and free....
Correct??
changes little if you are a novice and more than enough!!
I'm tempted to purchase because I found myself with a Dense THE.2 of a Volvo V70 2400i 20v 170cv 2001 that even the KTAG was a backup if not just flash the maps, for which I have made to help those who the UPA has the original.
Saw that it went to a good end all, I would like to gives me this atrezzo for my workshop.
This better, Wellon or X-Prog??
What is it NOT doing and what defects it has? In addition to the pliers fufa...
carlo abarth
05-11-2015, 19:12
the upa I think that is the best even if others are not!!! and always a subjective thing!!
Ok, the more complete is fine, but the loose change?? The advantages compared to other similar???
So all they say of the upa, he speaks well, but guides to the use there are many.
glittering chiffon party dress.fitted
In the help folder contents to find the necessary
A guide to the installation, is there? Since I have the dvd damaged.
Guys I have a problem I bought the upa v1.3 but in shipping it was damaged a installation cd,I contacted the dealer and they are waiting for the cd funzionanete but I would like to begin to test the product...does anyone have the installation files or can you point me on where to find them?It is not a tool ori of course
Powered by vBulletin® Version 4.2.2 Copyright © 2025 vBulletin Solutions, Inc. All rights reserved.