Light check engine alfa 159

[panterargento]

Hi to all,
I ? happened a strange thing, some day I set a map bought from the store...and up to here everything ok.
As st? doing tests maps, I made my way, I drop it in, all ok, but since it doesn't satisfy me, I return the one made here, the writing was good, as soon as I put in motion, the indicator illuminates orange "check engine"(I state that in the beginning there was the spy with this map), but the car is not d? no sign of drop in power ? v? well.
I do a few km + various reboots, but the light remains, then we write the file ori only with the egr off and fap off, light is still on, go back a few miles and after a few restarts, the light turns off.
I want to put the map is made here again...the light...I return the ori and after the usual procedure shuts down...
I repeat that with the light on I don't feel anomalies prerstazioni.
Honestly I can not understand, and yet with that map there, I shot a beautiful p? and without light, but I do not understand what it might be, maybe too many scriptures to us??
To someone ? ever happened to you?

[Tom79]

[emilground]

you have made a diagnosis to see what it is ?
could be a problem that is not strictly tied to the engine. Too much writing not consider their own, if they can do hundreds and hundreds ( c'? a physical limit of the eeprom but ? very high, about 1,000,000 of scripture )

[panterargento]

ok in the afternoon, will try? to make a diagnosis.

[Tom79]

[panterargento]

This ? the error: P061B calibration control unit

[tt225]

Some problem with the mod

[emilground]

clear the error and try to rewrite the map, sometimes can? happen that something goes wrong in the process of writing.
If, then, the problem ? presented to you when you have loaded the map mod you might as well be that not c'? a lot of consistency between the changes, and then it comes out that error.

[Tom79]

never seen this error... try to rewrite the map... and see if it appears the error..

[panterargento]

clear the error and try to rewrite the map, sometimes can? happen that something goes wrong in the process of writing.
If, then, the problem ? presented to you when you have loaded the map mod you might as well be that not c'? a lot of consistency between the changes, and then it comes out that error.

Error deleted, rewritten the map mod...all ok no error, the only strange thing that comes to mind ? was the fact that when I pulled the mpps from the obd, I turned off the instrument panel, but again ? a doubt of mine, usually I close the software, turn off the picture and out of the mpps, it may be that the rush to have missed some step...boh..., however, the important thing ? now not d? pi? the error.

[panterargento]

never seen this error... try to rewrite the map... and see if it appears the error..

In the workshop have speculated that the writing of the map was not successful to 100%, but ? a hypothesis, as to them this mistake ? again, maybe if someone's? pi? it would be good to understand better.

[Tom79]

look here someone has had the same problem and also on a 159 can you please post the link

https://www.professionalchiptuning.net/showthread.php?1467-edc-16c39-errore-p061b-calibrazione-centrallina

[panterargento]

By examining the map, I found a possible inconsistency on the turbo pressure...but I repeat "possible", the only retort ? the second limiter, which ? lower than the first.
I placed the screen.

[Tom79]

Unfortunately I can't look at still photos :-(

[panterargento]

Unfortunately I can't look at still photos :-(

Sin I had not noticed the messages, however, take a note of the discussion, and when you have the chance? if you can give them a look.

[marco]

the problem in question, the place anyway, it is a mistake to write penzo mpps is many times does a bit of casino write.

[panterargento]

the problem in question, the place anyway, it is a mistake to write penzo mpps is many times does a bit of casino write.

Yes, definitely when you write something must have gone wrong...

[tezzero]

? an error caused from the mpps in the closing phase of the map, i.e. at the end of the writing..sometimes it happens..

[marco]

however, I have become crazy to understand what had happened

[tezzero]

Often occur of the things that make us crazy..and they are almost all*******you

[frantik3]

it sometimes happens also with other instruments and the calibration in the ecu that is not done well with the file written data that is written to only the area of the data ,the only way to reset it, and write the ori clear the error and rewrite the mod for me and capitatpo many times with cock cmd mpps))))

[nuovaecu]

I don't think this is the error I done it so many times to pull the plug and never had any problems