clear tested 500 siemens VDO 51782985 5WK43808

[sno74]

as the title
clear tested 500 siemens VDO 51782985 5WK43808

[explode82]

it should I do,I open it but I can't find the e2p you know how to recognize it

[legendaryslave]

? smaller than those in the standard is close to the condenser in the anolo of the ecu if you take a picture you pointed to

[explode82]

I found it,but I do not know how to read it,counsel?

[sno74]

read it as a st 95320, or tell me what you read above.....

[explode82]

the problem ? that ? pi? small compared to the classical e2p,and I wanted to know which system to read it,if I have to unsolder

[sno74]

unsolder then there are adapters or solder, or the spring to put inside in the controller if the controller ? equal take a ep2 new and write it down clearly controls the frame for? maybe it was better that flipped open a post, otherwise the administrator then we scold if you need more there? problem......

[explode82]

After I ask him to change the post,but my problem is the video is not a e2p normal and smd

[sno74]

change the post and post photos cos? let's see.... I have gi? made three, I had no problems, also one of the new bravo ? similar....

[legendaryslave]

there are adapters weld-on or spring-or do as I did with the first wire small copper you connect on the pins in the pidinature ? equal to the e2p pin 1 is on the dot

[alexracing]

hello can you help me I with carprog I have problems ,I read with upa if I send you the file restores ,thanks.

[sno74]

Open a post indicating the hw and sw then let's see what you can? do....

[explode82]

put it that you retrieve quiet

[alexracing]

put it that you retrieve quiet

here it is, thanks to the availability

[explode82]

here it is

[alexracing]

thanks to the availability unfortunately, I can't still download from the forum if you do not ? a problem I can give you my and-**** ..................thanks again good job.

[msport (exil77grande)]

thanks to the availability unfortunately, I can't still download from the forum if you do not ? a problem I can give you my and-**** ..................thanks again good job.


the regulation that you probably have not read it prohibits what you asked for you,otherwise the limitations set it would make no sense don't you think?

[peppe82]

me and happened about 500 mtj with siemens vdo 51782985 I does crash but no go light on drivers of both the red and the yellow in the diagnosis before resetting gave sensor-front impact-shock rear right - side impact left after reset no fault xo spy on you, and never happened to you?

[explode82]

This happens when the sensors are not good, you can opt with a resistance, but ask the owner of the car if you want all the operating system or not, if not in the case of a further accident, the airbag is not bursts

[peppe82]

This happens when the sensors are not good, you can opt with a resistance, but ask the owner of the car if you want all the operating system or not, if not in the case of a further accident, the airbag is not bursts

by when should be the resistance? and then it should be placed under the seats

[alexracing]

I ? stumbled upon a great point, I've resolved with multiscan doing alignment proxi specific on airbag control unit

[peppe82]

I ? stumbled upon a great point, I've resolved with multiscan doing alignment proxi specific on airbag control unit

I tried already with proxi alignment but not va, errors in the ecu there are no lights are on. what do you advise me to replace the file that was?

[peppe82]

there someone who has the file ori of this ecu 51782985-5wk43908? can I write it with xprog with the setting of the serial eeprom-st - m95320?

[explode82]

hello check that all the sensors are good and have replaced the capsules explosive airbag

[alexracing]

I had the same problem alignment with other diagnoses have not worked with multiscan you