Tricks to detach tabs from the carcass of the ecu

[jared_poe]

I wanted to know the best methods and tricks to detach tabs of the control units from the carcasses.
I should do this on a edc7, as I read in the manual galletto 2 that there is a place to read in the bdm port with the e xxx bosch, but is located in the rear, I wanted to remove it but I'm afraid of breaking it if you do not perform the operations right ;)

[jared_poe]

This ? the photo of my ECU

http://img141.imageshack.us/img141/7250/img183w.jpg (http://imageshack.us/photo/my-images/141/img183w.jpg/)

Uploaded with ImageShack.us http://imageshack.us)

[admin]

We don't need to unplug the adapter to the connector for the bdm is above the red dot indicates the n1



http://img10.imageshack.us/img10/8516/edc7.png (http://imageshack.us/photo/my-images/10/edc7.png/)

Uploaded with ImageShack.us http://imageshack.us)

[jared_poe]

but in that pitch I have to use the e xxx marelli, on the guide of the galletto v2 I read that on the other side of the card (as I understood) c'? the pitch to read it with the bosch e xxx, do you know how to f? to remove it?

[Ross]

Sorry, what difference does it make to read it with a e xxx or the other?

[jared_poe]

[admin]

Why do you complicate your life, having the solution at hand for staccala you have to use the phono and the risk that you damage then you do

[giarras]

I, in your place, I'd listen to the advice you have been given,nn complicate your life.

[jared_poe]

ok guys I just wanted to know, for your information, if I happen to having to repair one that has a problem from the other side?
hair dryer and a screwdriver with a lot of delicacy, or there is some liquid to dissolve the damn pasta?

[admin]

Only hair dryer and a screwdriver

[savek]

admin always forget a lot of cold sweat :D

[matech]

trichloroethylene does not help?

it should not create any damage to the electrical components and / or to the...

[bobracing]

in the trade are of the solvents for these compounds silicone that will not ruin the board of the ecu

[matech]

could you kindly give a vague indication of a product?

I'm just addressing the ecu of a civic type-r that has the silicone around the connector, and I was looking for a solvent, for not too much strain on the plastic.

Just tried the trichloroethylene "avio,"something is, but not enough.

[munro]

I would say that you could use the common diluent to the nitro...
or try to ask a few of the body shop what they use as a solvent antisilicone before paint...
they'll pass on the bodywork before verniciarle because the silicon reacts with the paint, creating bubbles...
otherwise you may use a paint stripper with methylene chloride that ? a solvent based silicone use it for? a beautiful mask for organic vapours pech? it stinks so much, and certainly not good for you (and use of gloves, preferably nitrile). A similar product that I used ? "stripper dense" produced by solvea. Careful when you open it AND EXPOSE it TO the SUN
danger of death!!!!

[michell]

Fon screwdriver.and lots of luck.a council does not put any solvent because ec
Some component different from the other and you don't know what might happen

[munro]

sorry all for the uppercase in the post I escaped...I wanted to correct but not n? I have the chance..I hope to understand me not ? a "scream" but only a way of marking that the product and quite dangerous....

[michell]

I think that administrators have realized that there was a way to mark the sentence....

[chicco]

I instead of the screwdriver, use the spatulas to stucco those in steel, divide the effort on the surface more and make it flex less the card, cos? I pulled the cards is that edc16 edc17 without causing damage.

[matech]

Speaking of edc16 and edc17 now the practice ? consolidated: the heat-and-lift-rightly, in the manner pi? homogeneous as possible.

But take a certain ecu details, such as edc7 with which I am finding to have to do these days, the speech ? well pi? the complex!
The cover of the ecu ? silicone on the perimeter, and in the pi? also includes the two combs of the connector, they also siliconed in their perimeter! as if that wasn't enough, the pads of the bdm are on the back of the card, that ? glued to the casing on three sides with the silicone grey!
On a multilayer pcb as these I do not trust to try, no? less heat too. A solvent that ammorbidisse a little silicone would be liquid gold!

But body-builders when they have to replace the windshield glued together with the famous black silicone and clean inventories, using only methods "mechanical"?

[carlo abarth]

bob also to remove the putty from 59f???
in the trade are of the solvents for these compounds silicone that will not ruin the board of the ecu

[matech]

I just found a spry of innotec, gasket remover is called.

? the only one that ? was able to attack at least a little bit of the sealant of the ecu keihin honda, which I have in hand!

it remains for me to test it as it involves spraying it over an old electronic circuit, to verify that it is still not aggressive towards electronics.

My 2 cents

[nuovaecu]

or to the first but always with caution, it is made with the stripper model type hair dryer and screwdriver

[matech]

The Honda ep3??

you had the courage.... tap leverage with a screwdriver directly on the pcb by doing as you say you...

[nuovaecu]

I have heard of this spray to try it out for good and let us know how it behaves, perhaps, and the product would be convenient to all

[matech]

I have tried it and I have solved a problem.

I also tried to leave it on a pcb for a few minutes and did not damage.

Don't use it of course for every edc16 that I have to open it, but for those ecu delicate and special, I use it with success.