immobilizer on the old ecu iaw 8f 16f

[giulianoA3]

hello, somewhere I read that you just need to put a file on the eprom 27c512, for about 30 seconds, and replace the eprom oricinale, and the immo is off, ? can?of course, no welding etc?thanks

[egs]

No, you need to write the file scodifica on a 27c512 from scratch, and then desolder the mem. the original and solder the driver, and then perform the procedure ? pi? or less as you say. But in any case it takes the file scodifica.

[magi1984]

I for quelel units use the decoder 7 ------------, is the 8F - 16F - 18F without problems.
just ground pin of the micro-and upload the file, it does it all the interface and not dissaldi nothing.

the interface ? definitely a stuff to the chinese, and if you search the web you will find dozens of similar

[egs]

Yes, with the tool affixed to it, to? you can? make the file....

[giulianoA3]

No, you need to write the file scodifica on a 27c512 from scratch, and then desolder the mem. the original and solder the driver, and then perform the procedure ? pi? or less as you say. But in any case it takes the file scodifica.
ok, but the file scodifica ? the one that someone put here on the forum, where you talk to the immo?
certain units have the socket, and then you remove the eprom and moves without the use of welding if I'm not mistaken!!!!

[giulianoA3]

I for quelel units use the decoder 7 ------------, is the 8F - 16F - 18F without problems.
just ground pin of the micro-and upload the file, it does it all the interface and not dissaldi nothing.

the interface ? definitely a stuff to the chinese, and if you search the web you will find dozens of similar
sorry, but the name of the interface you can know?

[egs]

Some have the socket, and not welding anything. Regarding the file, I have mine, even if I have a tool licensed and the original, the one referred to by the magi I do not know, for? if you are looking for on the internet (as he says), you'll find him...

[magi1984]

sorry, but the name of the interface you can know?

? I wrote in my post... DECODER 7

[giulianoA3]

ok, I try to search !!!thanks..

[giulianoA3]

? I wrote in my post... DECODER 7
I was going to find, but I honestly do not understand where you know the price!!

[egs]

I this decoder does not know, try to ask the magi the price......

[magi1984]

no need to ask me. If he found it on the internet just contattar the companies that sells it and ask them directly

[redline]

hi I have one of the new tek and fantastic compared to others that I had before

[giulianoA3]

hi I have one of the new tek and fantastic compared to others that I had before

hello, where did you get that?how much have you paid?thanks..

[redline]

hello I give you my number call me I give you all the info 3200467120 michele

[egs]

Also I bought the.......... It's called the MID right?

[redline]

hi you, and so I am fine

[giulianoA3]

hello I give you my number call me I give you all the info 3200467120 michele
ok, thanks a lot!!

[egs]

It is, however, the price ? what I have said, at least I paid it so?.-..

[giulianoA3]

It is, however, the price ? what I have said, at least I paid it so?.-..
azz, I was thinking of something more economical to do by yourself!!!that amount should be good for at least a couple a month, in a year you recover the money you have spent..I do I do 3, then utilizzero only one, and then I should spend that!!

[egs]

Be you... I told you that you ought to be, if you had to do only those 3.... however, I am always available...

[giulianoA3]

Be you... I told you that you ought to be, if you had to do only those 3.... however, I am always available...
I'll keep this, thanks!!!

[egs]

[Mr.Flash]

hi guys, but what? the correct procedure for the eprom clock ??

this ? the one I tested on other types of marelli, years ago:
- mounts (socket or soldering iron)
- the ignition is switched on for 30 seconds
- off
- disconnect the immo
- it puts the eprom original

this led to a scodifica total.

? thing for 16F????

I attach the file in my possession for the scodifica of the 16F....... some good soul tells me if it is ok to use with the above procedure ??

[ugoboss]

the procedure is that both the 8 and for the 16f.

[Mr.Flash]

thanks ugoboss . And the file that I have attached ? correct x 16F ?

[ugoboss]

it is equal to what I have, I have already used then.......

[Mr.Flash]

perfect thanks 1000

[net_proo]

? very difficult to remove Motorola 68HCP11A1 ecu iwa8P, and read it or do immo off,
c'? the other solution for it or no???

[Mr.Flash]

8P ? ? enough the eprom...

[net_proo]

moderated message

[leandro89]

moderated message

write in English, use a translator to do it

[net_proo]

Mr.Flash
Mr. Flash is offline
THE AVERAGE USER

Join Date
Jan 2014
Posts
95

8P ? ? enough the eprom..


hello,

pu? explain very clear for or method of sharing ...