View The Full Version : Program gall v 54
hi guys from few days I bought a rooster and a jig at the opening of the cock, the nasty surprise there was no installation cd, someone has to pass me the program? then covering the template and the schedule are without tips welded I arrived packed in a sachet someone has the diagram?
thank you
To the appearance program to post it because it probably goes against the rules but if a admin gives me the go I'll post it gladly.
For the template I think to understand is that the black chinese right? You don't need any pattern you just need to put the test leads into the holes in the e xxx. In the bosch you can avoid the 2 tips that if you go to see in the scheme of some connection of control units from bosch, you will see immediately the tips are superfluous.
You'll notice, however, that I, with the schedule to spring chinese I have not found it all that well then look around you can find the schedule largest that you will arrive already soldered together and with the tips of much higher quality.
First of all, thanks a lot andrea1 sisi wait because I don't know if you can. For the schedule where tips to take them?
I have taken them from a friend but honestly, I payed them a little bit... because on ebay I've seen them at 50, but from the sellers on ebay you never know if they are already assembled, we would have to contact them and verify. I don't want to lose time and I paid for 80 but it's worth the expense. Unfortunately, I went to read a bosch with the e xxx spring until the readings required a little time everything is ok but if the reading took longer than one minute the reading was jumping.. Probably my e xxx had problems with slopes, because the welds were done well.
I understand thanks now just waiting for some administrator that enlighten us
At this point, search for it on ebay, so you can find anything.
At this point, search for it on ebay, so you can find anything.
only the program not the I found
only the program not the I found
I found it by searching for software fgtech v54
I found it by searching for software fgtech v54
but with win7 64 bit and easy-to-install?
Depends from pc to pc, I think because on my old laptop I had installed without any problems (win7 64bit) on the new, instead, I had a hard time (always win7 64bit) but it was.
First of all, I suggest ,no network and disable antivirus.
Hello all, after having procured the sw, however, I do not part with win 7 64 bit anyone know why?
hello savior feel I little cock for a while, and also updates, with the 0475 you can use it on win 8.1 64-bit, I can't guarantee on the 10 because it is still not installed and not tried, 0386 contrast only on win7 64-bit, the problem because you're not part of it and to see.....
hello savior feel I little cock for a while, and also updates, with the 0475 you can use it on win 8.1 64-bit, I can't guarantee on the 10 because it is still not installed and not tried, 0386 contrast only on win7 64-bit, the problem because you're not part of it and to see.....
Hello mistanggt thank you all for the response, I wouldn't know to tell you... I don't know if it is allowed by regulation to ask if you could connect remotely to give me a hand, logically, if you enjoy it and it is allowed. Still have not succeeded as I go to open the program, and the processor goes to max and then nothing opens. By inexperienced I was reading in the network of the fix may be?
Hello mistanggt thank you all for the response, I wouldn't know to tell you... I don't know if it is allowed by regulation to ask if you could connect remotely to give me a hand, logically, if you enjoy it and it is allowed. Still have not succeeded as I go to open the program, and the processor goes to max and then nothing opens. By inexperienced I was reading in the network of the fix may be?
to tell you the true I don't know if I am I also violating some rule.
the only way, and see, first of all, what is your configuration to the 0386 that the updated version of the 0754.
to tell you the truth, I do not understand why the choice not to have the pvt to help you.
I try to let the **** hoping not to be banned, and I apologize in advance with the admin if I'm violating some rule but it is clear that the aid in this case and free non-profit of the user who has requested the order to put it in terms of working with its box and original software.
in the case bacchettatemi but not bannatemi thanks.
electronics 1980* g m a i l . com
maybe before you send me a screen of what happens if you manage to capture it so we can also see if you have the sw right in such a case there are problems.
Powered by vBulletin® Version 4.2.2 Copyright © 2025 vBulletin Solutions, Inc. All rights reserved.