View The Full Version : rev limiter edc17cp04
Hi all, I'm avventurando just on the ecu, I'd like to be able to try the rev limit on a BMW 1 series 120d fitted with a edc17cp04 can you give me some tips? I have read several discussions but also if them for them it seems easy when you are in 2d out of the driver I can not see the engine rpm... in the sense that in 2D once you have identified the curve of the imitator, I find the ramp, but being out of the driver does not see the rpm how can I do ? you follow step-by-step up to the realization ? thanks in advance to all
Hello!first, you should post the details of your ECU,otherwise it will be difficult for those who want to lend a hand,then I read your post on another discussion and I can tell you that the proceedings on the edc15 for the classic popkorn is completely different from your ECU so be careful how you move.as far as the rides on the edc15 find them before the map lim.pair,and are displayed in the upper right corner of the case specific places to 5200.
In edc17 laps need to be converted with the conversion factor for this you do not see them in the clear like in edc15-16..
Also that the ecu is not port a only lim torque but different..
And I doubt that the method of the cutting axis rpm to work properly..
Would try..
In the case with lim torque it sizzles you can try to set the rev limiter drivers wish..
In the meantime, thanks so much for the responses... I have to say that I don't know much about conversion factors where can I find the tables if they exist? Except for now, on the edc 17 that I would be available as a guinea pig if you place the file ori you can guide me in the implementation ? The file ori and I have to post in the appropriate section right here is no good?
Thank you very much for the support
Check in the database that your file is not already present if not, there is loads of them and attach the link here in the tread..
If you just post the link of the file here..
For the conversion factors to find them in the damos in winols..
For the rest, I can help you..time permitting..
Thank you very much munro for the support; I've checked in the database was not there.
once you open the map within the torque limiter and I go in 2d and scrolling to the left I am a cake and a ramp that starts at the address 05822E but I do not have the conversion factors I do not understand the turns and then as you said, should have other limiters that do not know
Thanks in advance
I have not abandoned the quiet...
then 058044 you have the axis of the first lim of the couple and to change as in the guides related to the edc15..
the axis ends at 058068 where to see it written 9000 in reality, you have to divide the value of x2 in such a way that
to see the rpm in the clear..then set the axis for the last 2 position breakpoint value
where do you want the rev..logically you have to go to remove completely gasolo in the last break point dell
lim torque.. and a 16x1
another axis lim torque and relative limiter is in 0580AA the lim couple starts 0580D4 and a 21x1..
another still is in 058232(axis) and 05825c lim torque 21x1..
there are many other spri for the files, however, trying to properly set up these 3 then see what happens..
let me know..
Thank you so much for the clarification, for me, very important... then I arrived at the first bp 7800 that I increased to 8000 as it says in the guide edc15 i.e. 4000rpm if I'm not mistaken ;
then I went to the bp next which was 8400 and I took it to the 8010 then I went into the table and by 4000 rpm, then I have brought all the values to 0....you have been very clear but I am not sure I did it well, you place the file the rev-limiter I can't correct?( or did the same thing for all 3 controls which I have indicated).
Thanks again
I don't know why I do not upload attachments...it tells me error; I did, as usual, advanced mode, manage attachments, but when it loads it then says error
it is not necessary that you post the file if you've done all correttmente..
the method which is the safest and the one to load the map into the ecu..
then if you still want it to be at peace with the mind..ok look you can give..
a council is not to set it too low 4000 rpm, according to me, are a bit short, especially on an engine as fast as the bmw and is easy to find oneself in fourth or fifth gear at the rpm set in the rev with the car that pops..
alzalo a 500-800 rpm...
perfect the load and let you know...I agree with you regarding the rpm of the rev the sposterei at 5000 rpm it was only for test...
thanks again will update as soon as I did....thanks a lot
just tried the rev is not part...comes in, the limiter is normal at 4000 rpm precise can be caused by the fact that in the table I put everything to 0 from 4000 onwards? and maybe a 4000, I had to leave the original value?
thanks a lot for having guided you up to here...I did the rev it works...only that even if I set it to 4000 rpm for the test kicks in at 3000....the scoppietti does them well, but after awhile it is as if it disappears and remains the limiter normal...surely I made some error, place the file maybe I can fix thanks again...
not you need to reset the axis of laps, but only the surge after 4000 rpm......
the axis should be changed only after 4000 where to see it written 8400,i.e. 4200 rpm, set everything to 8020 so that you have the cutting rev 4010..
you aevo made a file but can not download so that you can not do anything about it..
thanks so much again for the support...your explanation is very clear but once you open the map came to me in a bit of doubt...
Then, starting from the first limiter to the address 058060 (8400rpm) I set everything to 8020 up to 058062 then after if I have understood correctly I should do the cut out on the limiter following that, however, is a panettone and a constant 5000rpm it down all at 4010?
on the second I did the same thing all at 8020 but in the panettone I have strange values with a peak of 3867 to address 0580e6 .?? how do I act?
as far as the last lim I did the same thing on the ramp and on the limiter, the next value to 4000 rpm the I have cut down to 0
can you please post the file for clarity ...thank you for having prepared the file, but unfortunately have not yet arrived to 80-mex
every patience has a limit...
if you don't understand I can't do anything..
Sorry if I made you become mad...you're only able to postarmi the file that you had prepared so when I get to 80 messages failed to understand?
hello, there are 2 bits to 11600 value, a little before the torque limiters.
Powered by vBulletin® Version 4.2.2 Copyright © 2025 vBulletin Solutions, Inc. All rights reserved.